Jump to content
SAU Community

Recommended Posts

hay guys i need some advice,

im looking at getting a new turbo for my r33gtst, The car has already a avo intercooler, full turbo exhorst, pod filter, full Link ECU running low boost and im making around 200rwkw on avos dyno.

i want a turbo that has stuff all lag and will give good low down power to mid range no to warried about top end due to, where are you able to use that top end power

so what do people think i will need to get in the power range of 220rwkw.

and will i need to get anything else other then a turbo.

Link to comment
https://www.sau.com.au/forums/topic/68292-what-turbo-to-get/
Share on other sites

hi flow the stocker i say. best response, cop and epa friendly. 100% bolt on. All the aforementioned turbos may bolt on to the manifold but most will require oil/water fittings. If its a stocker high flow, u can get any mechanic to do it or do it urself. Ie u don't have to take it to a "specialist" workshop that would charge thru the roof.

hey scott

if you want 220rwkw then go for a highflowed of your current turbo, should go same response as the stock turbo

if you want a bit more say 250rwkw then go hks gt-rs (its a gts-t turbo despite the name). it will be a little bit more laggier than your stocker but certainly the most suited to a mild rb25, theres stacks of dyno graphs with rb25 and hks gt-rs

however either way youll need to upgrade the following if you are still using the stock rb25 items:

airflow meter (youll be maxing the afm out)

injectors (youll be running dead on 100% duty or like 5% below at the moment)

fuel pump (it will be running out and can lean the car out, mine leaned out at 172rwkw)

clutch (youll be slipping with 220ish, definetly with 250)

again those arent 100% guaranteed but im maxing everything out at 172rwkw, youd certianly be maxing it out just as much if not a bit more at 200rwkw

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update all   thanks to the workshop manual, it lead me back to checking fuses as mentioned central locking and door open lights worked when acc was switched on. diagram attached shows two points of power 1. ACC and 2.  Batt with the later being fused (#28) I did check the fuses using a multimeter but I must have stuffed that up also. Went back and checked the batt fuse in interior fuse box and you wouldn’t believe it… a blown fuse. replaced fuse and everything is now working as it should including the climate control   thank you all with your positive insight and knowledge.    
    • Where is the warning "That this thread is super old"   I just went into a 5 year old thread, went to do a reply, and couldn't see anywhere obvious a warning of it being super old
    • Duncan is correct. Pitwork (and Toyota's own cheap brand "Drive Joy") were primarily created as brands to sell other manufacturers car parts. It would be weird if Nissan sold parts for Toyota vehicles with a Nissan logo on it, so they created Pitwork to sell parts for other brans Toyota, Honda etc. They are not the same as Nissan genuine parts, although they *do* meet Nissan's standards for replacement parts. They aren't supposed to be a substitute for genuine parts, but a cheaper alternative that is better than Ebay fake parts from you-know-where.
    • Thanks GTSBoy, much easier to work with it now it's free!  
    • I _think_ that one has a christmas tree or some other retainer spike into a hole in that panel under it. Come in under it with thin scredrivers and just pry it gently up. If you rip the ears off the retainer pin....so what? Just stick it back down after with a bit of race tape and carry on with life.
×
×
  • Create New...