Jump to content
SAU Community

Recommended Posts

Hey in the process of getting my RB25DET rebuild plans together, and was wondering what your thoughts on putting the N1 water and Oil pumps on?

IT will be a street car, rarely sit at countinious high rpm.

And i am lookin at getting 240-250rwkw out of it?

SO should i go for N1?

or is standard R33 gear up to the task?

Thanx

Link to comment
https://www.sau.com.au/forums/topic/69069-n1-pumps/
Share on other sites

Hey in the process of getting my RB25DET rebuild plans together, and was wondering what your thoughts on putting the N1 water and Oil pumps on?

IT will be a street car, rarely sit at countinious high rpm.

And i am lookin at getting 240-250rwkw out of it?

SO should i go for N1?

or is standard R33 gear up to the task?

Thanx

Try doing a search on this, it was discussed recently. From memory the N1 oil pump was just a standard one with a high tension spring. The water pump was designed for sustained high rpm use and not suitable for street driving. I'm pretty sure it was Sydneykid who posted.

Link to comment
https://www.sau.com.au/forums/topic/69069-n1-pumps/#findComment-1279334
Share on other sites

  • 2 months later...

Hey,

Any one with any more info on this?

I’m currently suffering the much seen "dropping oil pressure at idle, rectified by engine shut down and 3 min wait" This plus a audibly shagged oil pump, means I’m looking for a replacement.

UAS sell "N1 pumps" with visually different vanes " http://www.uniqueautos.com.au/pricelists/p...t_gtrengine.htm "

Worse case, the spring and vane are the only mods; what are peoples experiences, thoughts? do they overflow oil and just open the pressure spring more?

Much appreciated, and thoughts

- M

Link to comment
https://www.sau.com.au/forums/topic/69069-n1-pumps/#findComment-1430887
Share on other sites

The N1 oil pump is VERY different to the std unit - I recall seeing a thread not so long ago that did a detailed comparison between the std pump and the N1 pump - and the N1 pump proved to be VERY different - not just the spring.

From memory – it not only flowed more – but was considerably stronger in construction too (thicker backing plate for example). I can't seem to find that thread now – may have been dreaming – or it ?could? have been on the SDU site instead

For what it's worth (if you have lemming tendencies) I have both N1 water and oil pumps on my street driven GTR - and I've never had a problem with either of them (you can't be too safe with the slippery black stuff I think)

HtH

Link to comment
https://www.sau.com.au/forums/topic/69069-n1-pumps/#findComment-1431938
Share on other sites

From memory – it not only flowed more – but was considerably stronger in construction too (thicker backing plate for example). I can't seem to find that thread now – may have been dreaming – or it ?could? have been on the SDU site instead

I remember that post as well. I think it was from a guy that posts mainly on SDU but put the thread up here as well.

Was a good read .... I'll try and find it too

Link to comment
https://www.sau.com.au/forums/topic/69069-n1-pumps/#findComment-1432045
Share on other sites

I have had at least 5 genuine Nissan RB26DETT N1 oil pumps. There is NO DIFFERENCE to a standard R33GTR RB26DETT oil pump. However they are not the same as a standard RB25DET or RB20DET oil pump. The RB26DETT N1 oil pump has exactly the same oil flow rate as an R33GTR RB26DETT oil pump, the only difference is they have a stronger pressure relief spring.

They should not be confused with the aftermarket oil pumps from Jun, HKS, APexi etc. They are truly high flow as well as high pressure. This is confirmed by their cost which is 3 times what an N1 pump is sold for.

I have personally replaced 2 X N1 water pumps in RB26's that overheated in traffic. Put the standard RB26DETT water pump in and they have problems. The N1 pump is designed for zero cavitation at sustained high rpm, not low rpm in city traffic with the aircon on a 40 degree day.

The designation "N1" is for the Class of Production Car Racing, Nissan did not make these parts for a "better" road car. They are designed for circuit racing applications. It is that simple.

:D

Link to comment
https://www.sau.com.au/forums/topic/69069-n1-pumps/#findComment-1432397
Share on other sites

We don't use them:cheers:

Another question ...... :)

If you buy a standard 32GTR pump and replace the spring in it :

a. where do you buy the spring from?

b. what do you ask for when buying the spring?

c. how hard is it to change the spring?

Many thanks!! :(

Link to comment
https://www.sau.com.au/forums/topic/69069-n1-pumps/#findComment-1433162
Share on other sites

OK - so now I'm confused - this is the thread I was after. I did not search for N 'dash' 1 (N-1)

So - are they different or not ?

You'll notice that SK explicitly said the R33 GT-R oil pump, whereas the thread I linked was discussing the differences between the R32 GT-R and N1 pumps. Someone else will have to comment as to the difference between the R32 and R33 GT-R pumps.

LW.

Link to comment
https://www.sau.com.au/forums/topic/69069-n1-pumps/#findComment-1433395
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...