Jump to content
SAU Community

Recommended Posts

I wrote this down a little while ago, have a read but maybe let some of the other more knowledgable forum users look over it and pick out anything I've missed, which is entirely possible.

DISCLAIMER: While i have performed this myself and believe the below to be correct i am NOT a mechanic, I'm a backyard tinkerer, you do it all at your own risk. Just take it slowly and be methodical, don't rush anything, but if you're not confident in your abilities resign yourself to paying a mechanic to do it for you.

1. Disconnect power to the injectors (pretty sure they're grouped in to 3's and there's 2 plugs power them just trace the wires back and unplug).

2. Pull the coil packs off the spark plugs, leave the coils on those 2 rails in groups of 3, just undo the rails and lift.

3. Check your spark plugs now if you haven't already.

If there's nothing obviously wrong with the plugs put them back in and move on.

4. Pull all the rubber boots off the 6 coil packs, be careful the spings don't fall out the end, it CAN happen.  

5. IMPORTANT! Use something to mark the position of Crank Angle Sensor (a blob of whiteout overlapping the CAS and timing cover works).

6. Undo the 3 bolts and pull the CAS off.

7. Rest the coil packs so they're tips are a short distance from, but NOT touching, the head or anywhere that's well earthed.

8. Turn the ignition to ON (don't try and start it!).

9. Take the CAS in your hand with the little "stick" facing you and rotate that stick ANTI-CLOCKWISE.

You should get sparks leaping from the tips of the coils to the rocker cover one by one over and over. If indiviual coils spark sometimes and not others make sure there's a clear and clean path for it to spark to and from and that you're not turning it clockwise as it sparks unpredicatbly when you do.

To put it all back in, turn off the ignition, and go in reverse taking care with CAS, manipulate the stick until it slots over and the whole thing slides on, don't force it, then line those marks you made back up otherwise your timing will be out. Plug the injectors back in etc etc.

once the car is warm, just diconnect em one at a time, reconnecting.

if te idle doenst change... then youve got a stuffec oil pack

he can't do this unfortunately as his car wont start!

but yeah, that is the easiest way to test these kind of problems.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thank you, 100% the intent. New coils were due and the 17" sixers look/feel loads better than the stock wheels. The aero options are so spot on.   Thanks for the warm welcome, all!
    • 98 r34 gtt Been rocking my latest setup and car running like never before. Have put a good 200 miles on it since all the latest changes and additions. everything is dialed in and have been driving it a bunch.   However, all a sudden last weekend as soon as I pushed throttle passed 4k and the engine stumbles, (slow or fast acceleration) hesitates and doesn’t go above 4100 or so, like a misfire. Everything else seems fine. I had a “good” set of coil packs that I removed from car when I first got it when I changed them over to new coils. I swapped out current ones for those, but no change. I also changed the plugs, no change. Seems to rev over 4 when out of gear with no load just fine no “misfire”, but as soon as its in gear with a load of any kind, it “misfires” as soon as rpm drop back below 4 k it runs perfectly, smooth, starts, restarts and drives fine as long as I keep it below 4 k while in gear. All readings look fine, no CEL   Any idea as to what could all a sudden cause an issue when pushing rpms passed 4 k?
    • When you say your cams are 272/262 is that 272in and 262ex?
    • We're arguing semantics. I am saying 45 accel and a 55 deccel ramp are "2 ways". Even a 45 degree ramp and an 89 degree ramp is "2 ways", because it is literally... two ways. The cusco 55/30 ramp is a 2 way. It's two ways. I get it though - in normal nomenclature a "2 way" would be 45/45 or 55/55 or 60/60 i.e the same locking in both directions. And something like 45/65 would be considered "1.5 way". I would then say if we're getting into the nitty gritty then every locking diff is a "2 way" diff and we should not speak in 1.5, or 2 ways but ramp angles instead. Which ofc if one of those ramp angles is 90deg, that side is not doing any locking. :p So Nismo don't obviously sell 3 things. The fact of the matter that they only sell two items really goes to show that there's a 2 way and a "1,5 way" which is really a 1 way. I believe the actual lockup for the 'adjustability' of the GT pro is really just setting preload for when the ramps actually start locking up. It's not changing how much 'wayness' there is. It is (somehow) horribly explained. People just buy whatever diff and go "locks up good bruh" and that's what ends up on socials forever.  
×
×
  • Create New...