Jump to content
SAU Community

Recommended Posts

... i havn't really practice launch....ect but had a bit of play around with a 2004STI with the work on it and i just couldn't launch my Gtr right, only when we do a rolling start i was about 4 cars length in front but thats not important. I just want to learn how to launch my car right so when i hit calder i could have a good time.

Advices need please :)

Link to comment
https://www.sau.com.au/forums/topic/69825-how-to-launch-a-gtr-right/
Share on other sites

  • Replies 96
  • Created
  • Last Reply

Top Posters In This Topic

Take it to the track and practice. Much easier to learn when you have a proper prep'd track and a timeslip to gauge your efforts.

Start low, build up until you either break something or wheelspin and then go with what works best.

exactly what r32boys said......get it above 7000rpm and dont ride it, just release the clutch! if you go too low (rpm) then it will just bog and you will get flogged off the line. Hope you have a decent clutch though!

Yes i tried anything under 6000rpm and it just Bog down big time. I have after market clutch and i did try to ride the clutch and i've burnt a bit off it, dumb me.

I'm so used to RWD car, launch about 4,5000rpm and never bog down. Is it that easy to break something in a GTR by launching it at 7k?

I've done plenty of launches - only broke a gearbox so far, pretty sure that wasn't because of launching, it was 3rd gear.

If you want half launch i find you can get off the line quick even if your only on about 5000rpm, but you've gotta slip the clutch a little, but you'll need a strongish clutch for that, std one will just slip i think. But yeah you can launch at 7-8k as well, but i find just steping off the clutch doesn't work as well as easing it out.

I've done plenty of launches - only broke a gearbox so far, pretty sure that wasn't because of launching, it was 3rd gear.

If you want half launch i find you can get off the line quick even if your only on about 5000rpm, but you've gotta slip the clutch a little, but you'll need a strongish clutch for that, std one will just slip i think. But yeah you can launch at 7-8k as well, but i find just steping off the clutch doesn't work as well as easing it out.

What you mean by half launch? At which ...rpm? See you at Winton :)

Dumping the clutch or side stepping it will break driveshafts, stuff uni's and stuff your clutch center... If you watch all the japs how they do it is the nicest possible way for the best result.

Pull your handbrake on and leave your hand on it pulled up bring the revs to around 6.5+ and pull the clutch out till you can feel the car fighting the handbrake, from here release the handbrake and clutch at the same time and your away.... SOunds hard but by doing this the clutch is already semi engaged and nearly up to speed and all the slack has been taken from all your driveline components. Sure it burns the clutch a little but its no worse than any other method!!!!

What you mean by half launch? At which ...rpm? See you at Winton  :rofl:

Half launch .. dunno how to explain it, getting off the line without bogging down big time, but without launching full on... around 4000rpm and slowly rising the rpm as im slipping the clutch out. I've got a twin plate so its pretty strong compared to a stock clutch... I don't do it that often, as the others have said i'm sure it willbe burning it out doing that... but i found just stepping off the clutch felt to harsh on the car and just didn't feel as smooth.

Not sure if i'll be at Winton (not racing, might come for a watch) if i do, i'll take you for a quick drive to see if i can show you how i launch.

Half launch .. dunno how to explain it, getting off the line without bogging down big time, but without launching full on... around 4000rpm and slowly rising the rpm as im slipping the clutch out. I've got a twin plate so its pretty strong compared to a stock clutch... I don't do it that often, as the others have said i'm sure it willbe burning it out doing that... but i found just stepping off the clutch felt to harsh on the car and just didn't feel as smooth.

Not sure if i'll be at Winton (not racing, might come for a watch) if i do, i'll take you for a quick drive to see if i can show you how i launch.

Same here, not too sure now as i havn't found a proper set of rims for GTR, i'm running 17/8,5 and 17/9,5 so car handle a bit wierd for a 32Gtr also my Tein is wearing out a bit as well.

yeah i think i know what you mean by a half launch but i think my heavy duty clutch won't hold it as well as your twin plates therefor it will BOG down.

Good timeslips in a GTR comes at the expense of wear and tear - literally!

Decide if you have the spare cash for clutches, gearboxes, driveshafts or diffs before you try those rev limiter launches.

That said, a hell hard launch even in a near std R is bloody good fun!!

I've done plenty of launches - only broke a gearbox so far, pretty sure that wasn't because of launching, it was 3rd gear.

If you want half launch i find you can get off the line quick even if your only on about 5000rpm, but you've gotta slip the clutch a little, but you'll need a strongish clutch for that, std one will just slip i think. But yeah you can launch at 7-8k as well, but i find just steping off the clutch doesn't work as well as easing it out.

Werd! 4 Clutches and 2 Gearboxes say you're right.

Dumping the clutch or side stepping it will break driveshafts, stuff uni's and stuff your clutch center... If you watch all the japs how they do it is the nicest possible way for the best result.

Pull your handbrake on and leave your hand on it pulled up bring the revs to around 6.5+ and pull the clutch out till you can feel the car fighting the handbrake, from here release the handbrake and clutch at the same time and your away.... SOunds hard but by doing this the clutch is already semi engaged and nearly up to speed and all the slack has been taken from all your driveline components. Sure it burns the clutch a little but its no worse than any other method!!!!

This is the best method, and the one i use. It does take a little getting used to co-ordinating the right actions.

Just dialing up and dumping places too much shock on ALL the driveline components. Basically the handbrake method loads up the drivetrain and puts less stress on the components. Sure it is at the expense of clutch wear, but i would rather put new plates on my clutch than replace a gear in my dog box, or a drive shaft.

Basically there will always be some wear and tear with ANY method of drag racing. Its just up to you which part you want to replace sooner.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...