Jump to content
SAU Community

Recommended Posts

i just got my new engine and very nice indeed what do people think how much power i would make at the rearwheels in a r33gtst put your info in and i give you the honest power figure? as it follows in mods

Rb26 stroked out to 2.8

hks crank

hks rods

hks pistons

N1 nismo cams

hks valves and springs

mild port and polished head

hks cam gears

n1 oil pump

n1 water pump

1000 cc injectors

100 mm throtlebodie

pair of 3240 hks turbos

and running it with motec m800 ecu

3 half in dump pipes into 3 inch nur spec r blitz sys

and nice new pair of fuel pumps and new fuel lines tobe put in

and nismo fuel reg

this it was ive got done and now have all built ?

as im yet to put it in the car i just want peoples thoughts of what power im going to put out in the rear wheels

Link to comment
https://www.sau.com.au/forums/topic/70442-my-new-rb26-28/
Share on other sites

  • Replies 88
  • Created
  • Last Reply

Top Posters In This Topic

Wow big list of top shelf parts there, you must be aiming for the quickest land speed Skyline in the world! Did you spec the N1 cams to keep the head costs down or for better off boost performance? How about the oil pump, did getting the N1 version allow you to spend extra on the HKS goodness? What manifold are you running with the 100mm tbody?

Link to comment
https://www.sau.com.au/forums/topic/70442-my-new-rb26-28/#findComment-1301068
Share on other sites

Why? Just fit it into the car and find out for yourself. Hasn't the person that built it given you a power estimate, or is it a suck (build) it and see type thing?

Most GTR's running these big babies are in the 8's and have over 1200hp...

Link to comment
https://www.sau.com.au/forums/topic/70442-my-new-rb26-28/#findComment-1301179
Share on other sites

what crank is it to be 2.8????

As elluded to by doughboy, you have skimpted on some very important components that will prelong engine life, I believe if you are spending the money on 3240's you should spend an extra 2-3g on a good oiling and cooling setup like re-proprieting the cooling system!!! Good luck mate if everything falls into place should really see aroung 600kw at the fly!!!

Link to comment
https://www.sau.com.au/forums/topic/70442-my-new-rb26-28/#findComment-1301393
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...