Jump to content
SAU Community

Recommended Posts

  • Replies 56
  • Created
  • Last Reply

Top Posters In This Topic

thats good 'cause I use it!!! It was recommended by Meridian M/sports before I went to PI (high cornering speeds = more SBS) and as long as I warm the car up and don't give it stick till its properly warmed up the bottom end will stay intact.

I happen to know that the car in question (Archies) had gone from using Castrol at Calder to using Fushs at Winton.

If it is as expected a big end - what part the oils played in this is debatable. But until I see a GTR running overfilled Castrol oils do a big end I will not personally believe in SBS. LOL

If it is as expected a big end - what part the oils played in this is debatable. But until I see a GTR running overfilled Castrol oils do a big end I will not personally believe in SBS. LOL

I'm using castrol 10-60 as well on recommendation by a mechanic who races in some class (i forget which).

How much do you guys overfill the oil by for the track?

:cheers:

so the total oil you have in your sump is 5.5L?

a GTS4 has a gtr sump and it says 4.5l is what it takes with a filter change, i usually put in an extra .5L making it close enough to 5L.

Is that the same size for a R34 GTR?

Really...you think it would be as much as 1L?

I use Dash 10 hose, so has an ID of about 12mm i suppose. The oil cooler itself doesnt hold much oil at all as the tubes in the core are very fine, the end tanks would probably hold about 200ml though...so maybe a total of 600-700ml for my 19row oil cooler.

I only make the point in case there is an issue of running too high an oil level?????

Andrew sorry to say buddy, using Fuchs was not the reason for the failure, to even suggest one oil change could blow the engine is laughable.

The motor had major concerns b4 Winton, that's why Archie left Calder so early, the thing was pinging off its head. Archie also knew the internals were questionable and was warned (and agreed) on how long the engine would last. Why do you think he was soooo calm at Winton, after the blew it?

I have been using Fuchs for the last 3-4years and have never had any issues at any, track/fun day/drag/cruise/etc. I truly believe that this oil is just as good as the Castrol oil, but at the end of the day ppl make a judgement on what they know.

Not having a go at you, Andrew, just stating that there are alot of contributing factors in this car's particular life and that no matter what oil was used it would have ended in the same unfortunate way.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
    • Just one thing; tapping tapered threads is tricky. Taps are always tapered and you would generally run it as far as you can, but with a tapered thread you have to stop much sooner otherwise the wide part of the taper will run in too far and you will have to thread the sensor in too far too as well (possible that it will never make a good seal) BTW nice wide wheels, I guess the top one is for the back!
    • Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity. Edit: 11kg each (or 10.9/11.1 depending on what my scale decides over multiple tests, the 18x11 don't seem to weigh noticeably any more than 10.5)  
×
×
  • Create New...