Jump to content
SAU Community

Recommended Posts

I've got the following forsale.

Oil filter relocation kit $100 (suit RB engines) -SOLD

Black R32 GTR boot minus spoiler $90 - SOLD

R32 GTR Stock front pipes $50

R32 GTR Stock dump pipes $20

R32 GTR Stock front sway bar $30

Brand new Field One Connector for RB26 ECU $150 (its a wiring harness that goes between the ECU so you dont have to cut up the original harness to install things like a boost controller etc..something like the attached picture)

pm me for more details

Cheers

Could I get a little more info on the Field One connector? Do they have a website? Where exactly does it tap in to the loom (at the ECU I take it from your description)? Some close up shots would be great.

:P

Lucien.

Ronin 09

I dont mind sending the boot to Melb, as long as you pay for freight

lwells

I'll get a digital camera and take a pic. The way you connect it is as follows. The loom connects to the field one connector then the field one connector to the ecu, its a 10minute job.

cheers

Ronin, I will bow out and let you have it. I only wanted it mainly because it was cheap, and because my boot has a couple of holes in it from a wing that I have now removed. I will just weld them up when I can be farked. enjoy the boot :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • 75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
    • Trailer prep is underway... Lined up the wheel to get a rough indication of how it would sit Then removed all the bits (as far as possible) and gave the frame a light sand and quick lick of paint   Then added some carpet
×
×
  • Create New...