Jump to content
SAU Community

Recommended Posts

The Hicas system is uses the pwr steering fluid to run it's system. One of the warnings that you can get with Hicas is low fluid levels, which also means your pwr streering couls also be low (quite probably.) Check fluid and check for leaks around the hoses to the system. Leaks are not uncommon - GTR, GTS 300ZX, etc...

r33gts, I would recommend you first check the power steering fluid as that may cause the heavy steering, and the HICAS light to illuminate.

Alternatively check the connections to the electric HICAS unit behind the diff as some experience heavy steering when it is disabled.

The power steering in the skyline is variable, getting heavier at high speed so it may be some other electronic fault. With that in mind do a diagnostic check on the ecu as well.

  • 1 month later...
i have the same problem buy mine is caused by fitting an aftermarket steering wheel did you fit a aftermarket wheel?

Hey man,

I have an aftermarket wheel and my HICAS light is on 24/7.

Just wondering if yours is on ALL the time aswell or if its only on around corners etc.

Also has your steering become quite heavy since the new wheel?

For those with aftermarket steering wheel and boss kits, HICAS is a common problem.....firstly make sure your Boss kit is HICAS compatible it needs sensors in the boss kit.

Secondly, make sure your steering wheel is on straight......loosen it off again, drive along in a nice straight line say 20m, then pull the wheel off and put it on again. Then repeat until you are certain it is straight. HICAS will report an error if the wheel is crooked since it thinks the car is turning all the time :D

  • 2 weeks later...

Revolution race gear sell the HKB boss kit for HICAS equipped cars. Well they got mine in. My HICAS light comes on sumtimes after 20-30 mins sumtimes not at all. I think my car needs a wheel allignment, as either way i adjust the boss kit one spline either way is still out... Would this cause the light to come on?? There is a HICAS diagnostic isnt there?

Revolution race gear sell the HKB boss kit for HICAS equipped cars. Well they got mine in. My HICAS light comes on sumtimes after 20-30 mins sumtimes not at all. I think my car needs a wheel allignment, as either way i adjust the boss kit one spline either way is still out... Would this cause the light to come on?? There is a HICAS diagnostic isnt there?

yea my hicas light comes on after 20-30 mins driving also.. only really comes on if im a freeway or something..

also running a HKB boss kit with hicas support

Guys you can run a hicas diagnostic by following these steps:

Procedure:

➢ Switch ignition off, transmission in neutral or auto in Park.

➢ Start engine

➢ Very quickly (with a couple of seconds), turn the steering wheel left and right about 20

degrees from centre five times, and then pump the brakes five times, then press the

brake pedal once more this will enter diagnostic mode.

➢ Drive forwards or backwards about 5 metres at a speed less than 10km/hr, this will

enter full diagnostic mode.

➢ The HICAS light in the instrument cluster will be flashing quickly (for normal) or will

flash a code indicating any problems.

➢ Long flash = first digit, short flash = second digit.

➢ Diagnostics will return to normal after five minutes, or any speed over 10km/hr,

or ignition is turned off.

The codes are as follows:

HICAS Diagnostic Codes 1989-1993

1 HICAS solenoid right hand

2 HICAS solenoid left hand

3 Cut off valve

4 Power steering solenoid

5 Vehicle speed sensor

6 Steering angle sensor

7 Neutral position sensor

8 (Auto) Parking brake sensor,

(Manual) Clutch sensor

9 (Auto) Inhibitor switch,

(Manual) Neutral sensor

HICAS Diagnostic Codes 1993-1999

11 HICAS control unit

12 HICAS motor power supply not present

13 HICAS motor output not present

21 Vehicle speed sensor not present

22 Steering angle sensor not present

23 Steering angle sensor neutral or not present

24 Rear main sensor input not present

25 Rear sub sensor input not present

31 Parking brake sensor input not present

32 (Auto) Inhibitor switch input not present

(Manual) Neutral switch input not present

33 Engine speed signal not present

Hope this helps!

My light also seems to come on from time to time. When I start the car it stays on for a couple of hundred meters, then when I tip into conrners it comes on again, and sometimes when I give it a boot full in a straight line. Weird?? I have the standard wheel so I assume the boss kit hasn't been tampered with...

Does anyone know if the light is meant to come on whislt cornering?

  • 1 month later...

After running my R32 GTR in diagnostic mode the Hicas light flashes four times quickly and then the fifth flash is a long one. The Hicas light turns off for a couple of seconds before repeating the above sequence.

I have read the Hicas diagnostic codes above but I am unsure how to interpret them. Any help would be appreciated.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...