Jump to content
SAU Community

Recommended Posts

i got a rb25det gear box with tail shaft for sale. has aprrox 75000kms

no crunching or grinding, gear box is in very good condition. 1150 ono

also have an rb25 hi flow. Steel wheels and bigger exhuast wheel and insides have been bored and machined. made 213.8 rwkw on 16psi on my rb20 runin an safc and made 201rwkw on a rb25 on 11psi.

Turbo can run 20psi wif no problems as long as u got the stuff to back it up

This turbo has no shaft play and is in very good condition. only around 11000kms on it.Bolts straight onto the standard stuff so basically a straight swap nothin else needed for either the rb20 or 25 1000 ono ( cost 1300 to hi flow)

pm me if interest

Link to comment
https://www.sau.com.au/forums/topic/73009-gearbox-n-turbo/
Share on other sites

I am interested in the gearbox if you still have it. Does the gearbox still have the slave cylinder on it and does it come with a clutch. I am also after the slip yoke and uni at the drive end so the tailshaft can be cut after the uni for delivery.

Link to comment
https://www.sau.com.au/forums/topic/73009-gearbox-n-turbo/#findComment-1351856
Share on other sites

  • 3 weeks later...
i got a rb25det gear box with tail shaft for sale. has aprrox 75000kms

no crunching or grinding, gear box is in very good condition. 1150 ono

also have an rb25 hi flow. Steel wheels and bigger exhuast wheel and insides have been bored and machined. made 213.8 rwkw on 16psi on my rb20 runin an safc and made 201rwkw on a rb25 on 11psi.  

Turbo can run 20psi wif no problems as long as u got the stuff to back it up

This turbo has no shaft play and is in very good condition. only around 11000kms on it.Bolts straight onto the standard stuff so basically a straight swap nothin else needed for either the rb20 or 25 1000 ono ( cost 1300 to hi flow)

pm me if interest

Is the gearbox still for sale? PM me if it is. Thanks.

Link to comment
https://www.sau.com.au/forums/topic/73009-gearbox-n-turbo/#findComment-1385713
Share on other sites

  • 2 weeks later...
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
    • Just like in being 14mm too small (296mm) makes it not fit, being 14mm too big (324mm) it also won't fit. You want to find the correct rotor.
    • @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
    • I started removing the tank a while back with the intent to give it a proper clean. Got to a bolt that I couldn't undo completely due to a diff being in the way, so just said f**k it and siphoned the gluggy old fuel out and called it a day. Looking it the tank it looks less corroded than the one in the pics for that billet hanger from Frenchy's anyway. Isn't it the fuel filters job to worry about this stuff? I scraped off most the crusty shit of the hanger but will give it another go before reinstall coz maybe the fuel and return pipes are also full of gunk  
    • Pretty sure it is a common fault. I believe this is the only part you need, but don't quote me as I don't have a V36.  I also believe it is a bit of a pain to change and the device needs to be encoded to the car once it is replaced, so may need someone with the right tools. Buy Genuine Nissan 48700JF00D (48700-JF00D) Lock Set-Steering. Prices, fast shipping, photos, weight - Amayama
×
×
  • Create New...