Jump to content
SAU Community

Recommended Posts

Hey Guys,

I couldn't find a thread with the info, Probably cause I don't know the terminology, so feel free to link me if it has been discussed.

I need to get my camber adjusted both front and rear. Using bushes from whiteline etc are only going to get it *just*right with not much(any?) room for changing it more so. I was thinking if I am gonna spend the money, I would be better getting adjustable arms (if they exist for 32's) instead of bushes.

My car - 89 R32 GTST 4dr, it is standard except when it got here from Japan, I found it had HKS springs (lower) which puts hige negative camber on it.

So, my questions

1) Do they exist?

2) What is the correct term for them so I can search for them.

3) How much adjustment do they allow?

4) What are the brand names that sell them?

5) Where do I get them?

Thanks

Chris

Current Settings

Front

--------

camber = left = -2.08 right = -1.49

Castor = left 5.06 right 6.17

Toe = 0

------

Rear

-------

Camber = left -2.29 right -1.49

Toe = left 0 right -0.8 out

Link to comment
https://www.sau.com.au/forums/topic/73971-adjustable-camber-not-bushes/
Share on other sites

There have already been threads about this - try searching for SydneyKid's posts then looking at the title that suggests suspension settings.

I have adjustable camber plates on the front - I saw some on ebay for cheap (second hand cusco i think) recently.

For the rear I have a 'camber kit', I don't know what else it's called but yeah they're just arms really and I bought mine from garage-13.

Around 1 degreee negative camber on the front is my suggestion for a road car. The Whiteline camber adjustable bushes will give you that.

Around 0.5 degree negative camber on the rear is my suggestion for a road car. Two sets (inner upper and inner outer) of Whiteline camber adjustable bushes will give you that.

While you are doing that, I STRONGLY recommend a set of caster bushes as well, they need more caster badly.

The bottom line is, if you can't achieve those settings with the Whiteline bushes, then the car is too low. It is below the appropriate setting for good handling let alone acceptable ride. Check the centre of wheel to guard measurements, if they are below 350 mm, then its time to think about raising it.

Hope that helps:cheers:

Thanks guys.

SK I don't think it's too low, It's one of the highest I have seen! haha. I will measure it tonight tho.

So you don't think I'd be better off getting adjustable arms over bushes? I thoguth it would just allow more options later down the track.

Thanks guys.

SK I don't think it's too low, It's one of the highest I have seen! haha. I will measure it tonight tho.

So you don't think I'd be better off getting adjustable arms over bushes? I thoguth it would just allow more options later down the track.

I am not a fan of sphericals in a road car, they wear out very fast in that environment, knock like a bustard and cost as much as a new arm to replace. Plus they add quite a bit to the NVH (noise, vibration & harshness).

If it is trully high, then it must have badly worn bushes in both sides and both front and rear to have that much camber. That is unlikely, because they are so even, generally the LHS bushes wear much faster than the RHS. It will be interesting to see what you find when you get into it.

:cheers:

ok, so i measured tonight.

Front height from centre of wheel to gaurd = 330mm

Rear height from centre of wheel to gaurd = 340mm

Which is below the 350 you reccomended. So what how is this going to efffect the car? I wasn't planning on buying new springs.....

SydneyKid.

Do you think I should look at rasing the car before anything else, or is it going to be ok as is? What are the effects going to be with it being too low? It is fine to drive..I am yet to scrape out on anything.

Can you share with me the effects of having the car at this height. Assuming I fix the camber/Caster....what will be the problem with the hieght?

Cheers

Chris

SydneyKid.

Do you think I should look at rasing the car before anything else, or is it going to be ok as is? What are the effects going to be with it being too low? It is fine to drive..I am yet to scrape out on anything.

Can you share with me the effects of having the car at this height. Assuming I fix the camber/Caster....what will be the problem with the hieght?

Cheers

Chris

Hi Chris, sorry for the delay in responding, race meetings back to back are killing me.

Nisan designed the suspension geometry to work through a range of movement, when the static height is too low there are a number of problems;

1. There is not sufficient suspension travel to absorb bumps, so you get damage, cracked suspension mounting points, rapidly wearing bushes, broken windscreens etc

2. The dynamic suspension geometry goes out of its design parameters. You can set the static geometry (camber, caster, toe) so it is OK. But as soon as you compress or extend the suspension those settings change. Nissan designed in changes in geometry by its selection of mounting points for the suspension arms, an example being camber change. As you compress the suspension you get slightly more negative camber. So as you go around tighter corners the car leans more (compresses the suspension) and the extra negative camber helps the car maintain a good tyre contact patch. When you lower it too much, the suspension starts to go posiitive camber instead of negative, and you loose a lot of tyre contact patch.

3. You loose power, the drive shafts are not designed to operate at that angle and the CV's soak up more power. They also wear out much faster.

I can give you plenty more examples, front and rear toe change bump steer, steering axis inclination, loss of anti dive and anti squat etc etc. We spend a lot of time checking suspension geometry to determine ideal settings on Production and Improved Production race cars. There are optimum heights for all cars, where if you go below that, you end up with basket case of problems.

The reality is low is slow for a whole lot of reasons.:(

Alright, Thanks mate.

I just gotta decide what brand bushes to run now.

Without changing the springs, I can't run Whiteline front, cause they only allow 0.5 degree change. And I need closer to 1 degree.

The rear I could run whiteline tho. I can get 2 kits which will allow the adjustment I need.

Pedders said with their kit they can get 1.5 degree change on the front (they wanted to aim for -0.5) , and 1.5 degree change on the rear.

Is the stuff pedders use any good? Any need for me to fork out the extra for whitline? I'll have to see what noltec have.

Cheers

Chris

Talking to Noltec, these are my options from them.

Option 1 Total $1000 ish parts ex GST

N52088 - Adjustable upper arm $502.86 + GST

N82481 - Caster Kit $180.00 + GST

N62544 - Rear camber/toe kit (3 kits req.) $91.43 + GST per kit or $240 + GST

Option 2 Total $1550 ish parts ex GST

N52088 - Adjustable upper arm $502.86 + GST

N82089 - Adjustable radius rod $630.00 + GST

N62544 - Rear camber/toe kit (3 kits req.) $91.43 + GST per kit or $240 + GST

They also recommended these...can someone tell me what this will do for me?

N92447 - Subframe mounts $193.60 + GST

Those prices is higher than what pedders would do it for using their own parts. Is there any reason to not use pedders?

Whiteline Option - Total $671 ish Parts

KCA331 - Front Radius Rod Bush +/- 0.75 deg $117

KCA336 - Front Camber Adj Kit Upper Camber Arm +/- 0.5 deg $290

KCA347 - Rear Camber Adj Kit Upper Camber Arm +/- 1.5 deg with 2 kits $264

My 20 cents....

For your purposes I think the Noltec upper arms are an unnnecessary extra expense, the Whiteline adjustable bushes will do fine.

For your purposes I think the Noltec adjustable radius rods are an unnnecessary extra expense, the Whiteline adjustable bushes will do fine.

Subframe mounts, sometimes called "pineapples", stiffen up the rear sub frame (it is mounted to the chassis on rubber bushes) and remove most of that vauge rear end feeling.

;)

ahh pineapples. now that makes sense :cheers: Why don't they call them that ! haha

I figured the notlec stuff would be kinda a waste.

Well it's only an extra $100ish to go with whiteline over pedders stuff, so I guess I should do that

Do you think it's a good idea to look at different springs first? What springs do you usually recommned to people with stock suspension? Keep in mind I am on a budget, it has been suggested i could get king springs for $200ish all 4....that is do-able. Is it worth looking at new shocks as well? Or is that going to be too substantial cost?

I will have to buy another standard shock anyways, cause one of the tops is stuffed, and if I take it off I'll have to grind the nut off.

  • 1 month later...

alignement.jpg

as you can see, I have a bad camber problem can anyone point me to a relatively cheap solution in order to get that camber back to -1 deg.

I could buy adjustable, but damn 400$+

thanks for any help

oh here's a pic of my current set up, someone thought they might be nismo's

100_5820-1.jpg

Also what is suposed to be the length?? mine are 6" long :rofl: I'd like longer

Mate that is a seriously bad camber problem on the front. What springs/ride height are you using? First thing I would be looking for is worn bushes, rods and balljoints. A camber issue like that would not be due to solely the lowering of a car. I would be if surprised the tyres have lasted longer than 6 months of driving. Rear camber isn't that great but probably due to the combo of larger diametre rims/tyres, tein suspension and a lower ride height if you have that. Toe also needs to be adjusted on the front but thats simpily done in most cases by adjusting the tie rods, same with rear toe (search the forum for optimum toe specs)

I would suggest more things but after a big night I'm struggling to think atm :)

thanks for the replies.

there is no play at all with the wheel when jacked, I have juste replaced the tie rod ends my self(which explains the bad toe :rant: ) I indeed have tein, but I wouldn't know how to specify height, raising or droping height doesn't affect the camber with this type of suspension I was told.

I mesured from bottom of blocking ring to under the lip(the straight part at 2 5/8 inches I think.

anyone have a lentgh on the upper link?? If yours is also 6" long, it means I have another problem :|

Also ride height on the left side seems... quite lower even though I brought both springs to the exact same level... could the coil be finished? and I don't know the spring rates

(I got the car like that) hehe :werd:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...