Jump to content
SAU Community

Recommended Posts

afaik

Factory specs are 135-185 psi per cylinder and each cylinder being around 120 with an ~<5psi variance is decent for a >100,000km car.

Just means your car isn't in top condition, someone's had fun in it :D but it should be alright for a while (That's assuming my factory spec figures are correct)

i got mine checked it come out with all in the 120's but there all around them same  

broke that checked it said it was all good but that seems low to me is it ok

ingnore the other comments, outirght compression figures are not very relevant, as things such as how warm the engine is and battery voltage affect the outright figure.

what is important is that all figures are even, as it is unlikely that all cylinders have the same damage (if any).

usually a bad result would be say 5 cylinders having similar compression (within 3 or 4psi) and one cylinder (usually cylinder 6) having compression which is 25psi different.

as long as the figures are within about 3% from max to minimum its fine. so basically from what u explained the motor should be fine. if u really want to be sure do a leakdown test but that is usually only done if compression test turns out bad.

Knore's comment is sort of correct as most cars show compression around 155psi

they all got ok they got

1 124

2 125

3 125

4 123

5 124

6 125

is there a way to higher then compression

also i hear low compress means more lag

the tune is ****ed on the car so they r retuning the link computer the day i buy it they said thats y it is laggy and shit

they all got ok they got  

1  124

2 125

3 125

4 123

5 124

6 125

is there a way to higher then compression  

also i hear low compress means more lag  

the tune is ****ed on the car so they r retuning the link computer the day i buy it they said thats y it is laggy and shit

those compression figures are fine.

also the compression u are reffering to when u say it means more lag is something u cannot change. what u are reffering to is the compression ratio, ie. the relationship between the volume of air in the cylinder when the piston is at the bottom of its stroke compared to when its at the top.

u can make it less laggy with good tuning, although with a stock turbo it shouldnt be laggy either way.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
    • Actually, I'd say all three are the automatic option. Just the different trim levels. The manual would be RSFS, no? 
×
×
  • Create New...