Jump to content
SAU Community

Recommended Posts

i always wondered what that was too...

possibly an emissions sorta thing? i know the turbo cars don't have it and require a charcoal box for importing - but mine didnt need one (charcoal box) so i figured this could have been it?

:confused:

Link to comment
https://www.sau.com.au/forums/topic/75818-air-resonator/#findComment-1391095
Share on other sites

I think it has 2 purposes:

1. reduce intake noises (like a resonator in an exhaust system)

2. provide a reserve of air for the engine to take in should you suddenly floor it

I read an article from a link in a thread on here somewhere that experimented with removing this and replacing it with a straight pipe. The engine lost torque and intake noise was louder with it removed.

Link to comment
https://www.sau.com.au/forums/topic/75818-air-resonator/#findComment-1391187
Share on other sites

I think it has 2 purposes:

1. reduce intake noises (like a resonator in an exhaust system)

2. provide a reserve of air for the engine to take in should you suddenly floor it

I read an article from a link in a thread on here somewhere that experimented with removing this and replacing it with a straight pipe. The engine lost torque and intake noise was louder with it removed.

Its used to stop reversion through the intake system during throttle transients. Its not used to provide a resverve of air for snap throttle. They also used them on all the older XR6's and maybe the 8's cant quite remember.

Link to comment
https://www.sau.com.au/forums/topic/75818-air-resonator/#findComment-1391977
Share on other sites

I have removed the resonator and replaced it with a piece of 3" pipe, on my R33 GTS25, I don't know about the car loosing torque, but without the resonator the induction is quite noisey, when the engine is under load, it kinda screams as it hits 5500rpm.

I'll post up a pic tomorrow of the set up I have got.

Link to comment
https://www.sau.com.au/forums/topic/75818-air-resonator/#findComment-1392329
Share on other sites

because turbos presurize the intake air, where as the intake air on an NA is sucked through, but not continuosly, it pulses at high frequency, the chamber acts as a damper and smooths the air being drawn through. there was a big right up and tests done a while ago in HPI, different sized ones give different amounts of power and torque, sacrificing power in other areas, and a decrease all round without one.

Link to comment
https://www.sau.com.au/forums/topic/75818-air-resonator/#findComment-1393619
Share on other sites

  • 3 months later...

I Have done this mod, as I said in an earlier post since then I have had a bit of time and experimented around with it, and after a few back to back road tests there is a loss in torque, not a great deal but still noticable.

With out getting both systems dynoed It's hard to tell which has the better top end power, but with the custom intake the car has awesome induction noise :)

Link to comment
https://www.sau.com.au/forums/topic/75818-air-resonator/#findComment-1605934
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thank you, 100% the intent. New coils were due and the 17" sixers look/feel loads better than the stock wheels. The aero options are so spot on.   Thanks for the warm welcome, all!
    • 98 r34 gtt Been rocking my latest setup and car running like never before. Have put a good 200 miles on it since all the latest changes and additions. everything is dialed in and have been driving it a bunch.   However, all a sudden last weekend as soon as I pushed throttle passed 4k and the engine stumbles, (slow or fast acceleration) hesitates and doesn’t go above 4100 or so, like a misfire. Everything else seems fine. I had a “good” set of coil packs that I removed from car when I first got it when I changed them over to new coils. I swapped out current ones for those, but no change. I also changed the plugs, no change. Seems to rev over 4 when out of gear with no load just fine no “misfire”, but as soon as its in gear with a load of any kind, it “misfires” as soon as rpm drop back below 4 k it runs perfectly, smooth, starts, restarts and drives fine as long as I keep it below 4 k while in gear. All readings look fine, no CEL   Any idea as to what could all a sudden cause an issue when pushing rpms passed 4 k?
    • When you say your cams are 272/262 is that 272in and 262ex?
    • We're arguing semantics. I am saying 45 accel and a 55 deccel ramp are "2 ways". Even a 45 degree ramp and an 89 degree ramp is "2 ways", because it is literally... two ways. The cusco 55/30 ramp is a 2 way. It's two ways. I get it though - in normal nomenclature a "2 way" would be 45/45 or 55/55 or 60/60 i.e the same locking in both directions. And something like 45/65 would be considered "1.5 way". I would then say if we're getting into the nitty gritty then every locking diff is a "2 way" diff and we should not speak in 1.5, or 2 ways but ramp angles instead. Which ofc if one of those ramp angles is 90deg, that side is not doing any locking. :p So Nismo don't obviously sell 3 things. The fact of the matter that they only sell two items really goes to show that there's a 2 way and a "1,5 way" which is really a 1 way. I believe the actual lockup for the 'adjustability' of the GT pro is really just setting preload for when the ramps actually start locking up. It's not changing how much 'wayness' there is. It is (somehow) horribly explained. People just buy whatever diff and go "locks up good bruh" and that's what ends up on socials forever.  
×
×
  • Create New...