Jump to content
SAU Community

Recommended Posts

  • Replies 345
  • Created
  • Last Reply

Top Posters In This Topic

Buddy Club P1 QF FORGED with comp rubber 7.4kg rim weight

18x10 +12 all round.

114.3 5 hole

Falken Azenis semi comp 245/40/18

GT-R suitable.

one slight scratch on one rim. No gutter damage whatsoever.

$3000 landed. ( coming soon )

kaireican-img600x450-1123988210dsc05354.jpg

sure thing Rick.

we so require a 50% securing deposit prior to bidding/purchasing.

Once we have secured the product, shipping takes approximately 6 weeks to reach your door. Once they have landed here in sydney, we request final payment prior to sending the product to you via local courier.

HOLY CRAP!

I was under the impression it was the whole asking price then we receive the goods?

HOLY CRAP!

I was under the impression it was the whole asking price then we receive the goods?

50% up front.

50% once goods land in Australia.

Goods not released until payment is made in full.

i think that makes it clear. :)

  • 2 weeks later...
NISMO LM GT3

18x10 +20 all round GT-R suitable.

two rims have very slight gutter mark.

Dunlop FM-901 rubber 275/35/18

Closing August 29th. This set will sell and won't be relisted.

$2700 landed

tera374638-img600x450-1122201523dscf0459.jpg

tera374638-img600x450-1122201562dscf0461.jpg

They relisted - 128,000 "buy it now" ! Tempting but does that rubber look fairly worn out to you? Can't tell, bad angles. What does the text say about it?

  • 2 weeks later...

TBee,

these are more suited to the R33 and R34.

however, being a 9.5" rim, the +12 offset will certainly bring the wheels out to the edge of the guards, perhaps lipping of the guards will be enough. will double check.

ok, just checked... these were originally on a R34.

i know 10" rims can fit under a R32 with a +22 to +25 offset.

given those specs, these rims are a 9.5" width, taking into consideration that the offsets are bringing the wheels out a further 10-12mm with only 6mm less rim on the outer, these wheels will be sitting approximately 6mm further out than a 10" with a +22ish offset.

slight rolling of the guards may be needed to get these babies to fit.

estimating between $2500 and $2800 landed at this stage.

How much do you think those GramLights 57C will go for ?

I'd be only really after something with almost brand new rubber?

Cheers

That set in particular closed nine days ago, as mentioned on the post.

( September 7th )

I can source out some other rims that may be of interest.

Do you have sizes in mind?

17 inch 9/9.5 wide? rubber included i pressume.

Cheers.

Volk Racing GT-C in BLACK

18x9 +18 all round.

GT-R suitable.

Bids close September 23rd.

moro3_2000-img600x450-1126833718img_1001.jpg

Work Meister S1

18x9.5 +20 all round. some minor gutter scuffs.

Yoko rubber. 265/35/18

6-7mm tread

Closing September 23rd

from $3600 landed

miyupapa11-img600x450-1126859273aomori_108.jpg




  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...