Jump to content
SAU Community

Recommended Posts

Love these...still available?

VOLK GT-C 19x10.5 +21 all round.

Potenza GIII rubber with 9mm tread. IMMACULATE

Perfect package for an R34 GT-R or similar

Closing August 13th

$4k  (caps $100 extra)

nekomusume_gose-img600x450-1123497261img_4452.jpg

  • Replies 345
  • Created
  • Last Reply

Top Posters In This Topic

Love these...still available?

These have been relisted by the seller. Assuming the previous buyer pulled out. Volk GT-C with Potenza GIII rubber. *** listed two posts above ***

Closing October 1st.

  • 2 weeks later...

WORK VS-KF 19 inch!!! R32, R33, R34 GT-R

19x9 +21

114.3 5 hole wrapped in Pirelli P-Zero nero rubber.

2500 kms total travel.

not often seen in this condition.

Closing October 14th

estimating $2600 - $3000 delivered.

knm735-img600x450-1128669013kif_1487.jpg

knm735-img600x450-1128669025kif_1488.jpg

  • 4 weeks later...

Charles,

since you have not connected me for over a week and won't answer my PMs

can you please give me more information here about the rims I have ordered.

The auction closed 30th september and has arrived in sydney and landed in sydney on 12th nov and still haven't got them yet.

white TE37 17x9+22 $3100.

Michael

Charles,

since you have not connected me for over a week and won't answer my PMs

can you please give me more information here about the rims I have ordered.

The auction closed 30th september and has arrived in sydney and landed in sydney on 12th nov and still haven't got them yet.

white TE37 17x9+22 $3100.

Michael

Michael,

Ya got a PM regarding your new shoes. they are here and very much landed.

all good!




  • Similar Content

  • Latest Posts

    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
    • This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
    • Thanks for doing that Duncan! Makes you a good person in my books. We don't get kangaroos or wombats here. But we have bats and it's similar. AFAIK it's often the mums with a baby attached that get hit because they drop lower when starting from a tree. If you hit an animal, check on it. https://www.ifaw.org/au/resources/wildlife-rescue-app An app to get the closest wildlife rescue contact.
×
×
  • Create New...