Jump to content
SAU Community

Recommended Posts

  • Replies 127
  • Created
  • Last Reply

Top Posters In This Topic

lwells - I can definitely get the power fc pro for your GTR. I will post prices shortly.

HLT4Eva - Ive added you to the list.

rob1981 - Ive added you to the list and PM sent.

:P

WetGTR - PM sent.

lwells - heres some prices.

APEXi Power FC PRO (R32 GTR) - $1090 delivered

APEXi Power FC PRO & Cmmander (R32 GTR) - $1460 delivered

Note - the PRO units are made to order from Japan and will take from 2-6 weeks for delivery.

lwells - heres some prices.

APEXi Power FC PRO (R32 GTR) - $1090 delivered

APEXi Power FC PRO & Cmmander (R32 GTR) - $1460 delivered

Note - the PRO units are made to order from Japan and will take from 2-6 weeks for delivery.

Thanks for that. Bit more than I want to pay: put me down for a standard R32 GT-R unit.

:)

Lucien.

what is th dif between pro and the one i am geting what is the price dif and the pformance dif and is it worth spending the extra money for 97 r33

It depends on what you want to do with your car.

The power fc pro is designed for drag racing use.

These units have 2 additional functions over the regular units:

1. Ignition cut used for rev limiter - Regular Power FC cut fuel feed when the preset rev limit is reached. At high rpm there is the possibility of knocking when the fuel is cut in high powered cars.

The Power fc Pro cuts ignition at the rev limit to prevent knocking that could potentially destroy the engine.

2. 0km/h rev limiter setting - Allows for the setting for an initial rev limiter that is active whilst the car is not in motion.

This allows for maintaining a rpm level for constant launches.

Similar cost and lead time to the GTR version as mentioned above.

:)

since the other one is gone... when do u need payment by? coz im really broke atm

Close date - 12/07/05

Payment due - 14/07/05

I'll send payment details to all the buyers before the close date.

:)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • @Haggerty this is your red flag. In MAP based ECU's the Manifold pressure X RPM calculation is how the engine knows it is actually...running/going through ANY load. You are confusing the term 'base map' with your base VE/Fuel table. When most people say 'base map' they mean the stock entire tune shipped with the ECU, hopefully aimed at a specific car/setup to use as a base for beginning to tune your specific car. Haltech has a lot of documentation (or at least they used to, I expect it to be better now). Read it voraciously.
    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
×
×
  • Create New...