Jump to content
SAU Community

Recommended Posts

Ohh finally I have experienced 33 stock turbo shitness.

On a cruise today, grabbed for 3rd gear and bannnnnnnnnng.

turbo sounds like a jet, really bad. I think the bearings ****ed up big time, at least it didnt spit out the exhaust wheel!

Ohh well - anyone got any suggestions or have a upgrade for sale! Im looking for low mount, stock manifold internal gated replacement.

Link to comment
https://www.sau.com.au/forums/topic/79202-i-blew-my-turbo/
Share on other sites

I have it set on 10, but usually, its gets a initial spike to 13 psi and drops, It somehow responds very quickly.

Its either now GT2530 or 2540 turbo.

Anyone got one for sale or know of one for or coming up for sale, please let me know.

Regards

Kim

Link to comment
https://www.sau.com.au/forums/topic/79202-i-blew-my-turbo/#findComment-1444696
Share on other sites

I have it set on 10, but usually, its gets a initial spike to 13 psi and drops, It somehow responds very quickly.

Its either now GT2530 or 2540 turbo.

Anyone got one for sale or know of one for or coming up for sale, please let me know.

Regards

Kim

Id go the gcg highflow with a vg30 exhaust housing for sure. If I were going something from HKS a GTRS or a 2535

Link to comment
https://www.sau.com.au/forums/topic/79202-i-blew-my-turbo/#findComment-1448031
Share on other sites

Money talks. If you have the extra cash to buy HKS, you will end up with a better quality built turbo, a turbo that has been engineered to acheive the power@ higher boost, and better reliability. Also the turbines in a hi-flow turbo can be too big for the housings, which can cause other issues, such as fluttering while making boost.

That's an interesting comment Al, why do you say that over a high flow?
Link to comment
https://www.sau.com.au/forums/topic/79202-i-blew-my-turbo/#findComment-1450144
Share on other sites

your talking about brand new parts which is machined by gcg and balanced

how could they sell you something that isnt balanced or not fitted properly?

if it was a second hand bits or catridge or somethinf yeah ok could be issues

but not with a new bearing kits etc in it, dont see how?

i dont see how hks can make a better turbo when garrett make them in the first place

do you mean the combos avaiable and r and d they put in? you can always get whatever hks in garrett format, just gotta look around and ask the right people

anyway i dont really know what im talking about my clutch is angry and im still on stock turbo so who knows :confused:

Link to comment
https://www.sau.com.au/forums/topic/79202-i-blew-my-turbo/#findComment-1450275
Share on other sites

anyway i dont really know what im talking about..........
no arguments there...........:wassup:

The argument of "HKS Vs Garret" was been discussed numerous times, so everyone is entitled to their opinion.

The term "Hybrid", by definition means; "thing composed of incongruous (mismatched) elements." Now how can you argue that the hybrid turbo can compare to a HKS turbo. The amount of $$$$$$$$'s, research and engineering will greatly out way any Hybrid.

As stated b4, I myself have bought a second hand GCG hybrid and am very happy with the power, but know that a HKS turbo is far more superior. The HKS may not make a mountain load more power, but is an overall better product.

Link to comment
https://www.sau.com.au/forums/topic/79202-i-blew-my-turbo/#findComment-1450461
Share on other sites

guys

I would go for a Nice HKS or Trust or Apexi turbo ,but the MAIN thing that worries me is E P A!!

If I was back in Perth now, itd be getting HKS T04Z treatment, 50mm external gate, Motec, big fuel system, injectors and possibly even forged internals.

If I do this here, I will be raped by police again, I learnt my lesson on modified cars here, and Im defeinetly not gonna be pulling off shit evry time I get a EPA, we modify our cars to enjoy them, not to be looking over ur shoulder every time for a cop or worrying about someone dobbing you into the EPA.

I want simple stock looking high flow, bit more power and a newer reliable turbo.

Link to comment
https://www.sau.com.au/forums/topic/79202-i-blew-my-turbo/#findComment-1451088
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
×
×
  • Create New...