Jump to content
SAU Community

Recommended Posts

As some of you are aware, Andrew and I are doing a road trip in Sinbad to good ol sunny Cairns in 2 weeks.

I've finally convinced Andrew that we should put mesh over the cooler, it's the one thing I'm concerned about.

The paint is easily fixed, it's ****ed anyway, so I don't really care if it chips. The cooler on the other hand, I don't really have $2500 to replace.

So, if someones got some mesh lying around that they don't want/need (big enough to over lap the M-Spec front bar hole), and would like to donate it to my "help erin protect her cooler on the way to cairns" cause, please let me know!

Alternatively, we can just go to supercheap and pick up some of their mesh for $30 and some sikaflex for $25 and be done with it.

In true Andrew style, he wants to use zippy ties :P

So if anyone can help me out, please post here!

Link to comment
https://www.sau.com.au/forums/topic/80048-help-i-need-some-mesh/
Share on other sites

No :rofl: Not kangaroos.. Just rocks from hitting my intercooler.

I've been informed that we can use sikaflex by 2 different guys that work for panel beaters. Apparently we can just "heat it up and pull it off" when we get back.. Has anyone used/done this before and can confirm it?

Don't use heat risitant Sikaflex...use the regular one otherwise it will be a bitch to remove without melting your front bar...

Also another idea that I have used before is wire fly screen from Bunnings, the plastic stuff would most likely not be strong enough!!!!

Dankies Jason (oops.. I mean Melv) :cheers:

Someone did mention fly screen but we are a bit concerned it wouldn't hold up over 4000k's... is it really that strong?

Erin, your car is fast, but it dont do 4000kmh. It should be fine. Just supervise Andrew if he is putting it on, make sure its done rite :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
    • The axels in my R33 seem tired, and have a bit of play in them. I cannot find any new of course, not interested in buying used, but I am looking to see if anyone can identify some cross compatible axles. In the states I have seen suggested for S chassis the J30 axles, however for the skyline (as best I can tell) the lengths are about an inch off (2.5cm) on both sides. R33 my measure L 22" R 24.5" GPT L 22.5" 24.25" J30 L 23.5" 25.5"  so shaft length is probably an inch wider. Not sure if someone has another still remanufactured option besides the J30. I figured worst case I can buy a pair tear them down and swap the center shaft. My other option was reaching out to GSP to see if they cannot piece together a set, since the axle stubs are still manufactured, I wouldn't think it be that hard to find a shaft or make a shaft work. 
×
×
  • Create New...