Jump to content
SAU Community

Recommended Posts

ahahahaha i had to drive home with my pants undone :P

the russian guy kept saying "dont stop for a break.... or u wont be able to eat anymore... and when u cant eat any more... have a break for 10 minutes and start again... u'll be right" :)

Careful, that place isn't for Greenhorns! :P

mmm.... is it bad that I really want a steak at 8:45am??? :aroused:

Hey Ni

If you are ever up for a huuuge feed nearer home theres a restaurant called Limors (I think thats how you spell it) on Kooyong Rd in Caulfield. Meals are sooo big they are falling off the dinner plates and I should mention that they use platter sized plates :D

yeah... ferni double booked himself when i booked us in last time... so i had to suffer and miss out :D

they got ribs? *drools*

ant, i know about limours, man... was practically there EVERY weekend when i was in uni... mmmm... ribs... they have a sister resturant somewhere else also, but under a different name... that doesnt help much does it?...

If you are ever up for a huuuge feed nearer home theres a restaurant called Limors (I think thats how you spell it) on Kooyong Rd in Caulfield.  Meals are sooo big they are falling off the dinner plates and I should mention that they use platter sized plates :D

I agree with you Ant, the meals at Limors are massive!!

I agree with you Ant, the meals at Limors are massive!!

hey inark sounds good i will be checking it out on wkend..., a nice place i been to is called little malaysia order the banquet there about 30 per person and fills you up and is very nice imho if anyone else has eaten there?

cheers

There's also a place in Ormond called "The Steak Bank"

That's all that's on the menu.

You can buy a 1kg New York Porterhouse.  It's fuggin massive!

ooooo yeah ive been there a couple of times...

omg i wish josie didnt make me diner tonight for work... id be going straight there after work.

danny - shut up fool! :)

oooooooo adding all these to my list of places to gourge myself at :)

while we're at it...

Anyone been to Urban Burger??? omg... fantastic burgers and chips... my favs the wasabi one... im a bit of a wasabi fiend... i have it on everything... even peanut butter on toast lol

They have the best burgers ive had for a long time... and also the strangest :)

http://www.digitalhive.com.au/clients/urbanburger/

Yeah Rushie I know what you mean.....first time I went there with a mate we each ordered a schniz.....should have seen the look on our faces when the meals arrived :P My mate is still impressed that the only thing left on my platter was the salad!!!

Oh and I think the sister restaurant is called Maxi's and its on Glenhuntly rd near Nepean hwy

Oh and I think the sister restaurant is called Maxi's and its on Glenhuntly rd near Nepean hwy

thats the one....

same size servings, both are huge, but quality of food is not so good...

How is the quality of Blue Fire Grill compared to these 2???

3 course... oooooooo not sure. all i know is if u get the churiscarria that its about $45 a person thats basically ur entree and main and then some :rofl: so add desert (if u even have room) and drinks on top of that.

i got josie the lobster which was about $60... ive also had a fantastic steak which was about $29... the menu should be on their site.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...