Jump to content
SAU Community

Recommended Posts

Just a question regarding reliability as I am an ex-Commodore owner and they are probably the most unreliable cars I have ever owned. I moved up to a Skyline after owning several HSV's and V8 Commodores because I loved the style, power and quality of the R33's. So far my Skyline has been very reliable with none of the rattles or squeeks that I had in my Commodores and only basic things needing to be replaced as you would expect from a 10 year old car (fuses, globes, brake pads, clutch etc). How has your Skyline served you so far?

Link to comment
https://www.sau.com.au/forums/topic/81099-how-reliable-is-your-skyline/
Share on other sites

had the car for a month then the coilpacks started to die, its a given though since r34s are known for their coilpack failures. other than that the skyline is alot better than my old commodores, however the supra seemed to have a slightly better motor, ran silky smooth, the nissan motors are a little noiser.

Coils do die but once replaced you can forget them.

They are very reliable unmodified but you can show up slightly weaker area with modification. The same is true for any car.

They don't get the dodgy squeaks and rattles, bad door closing/openings and stuff so much though so that is good.

Turbo died while having new exhaust fitted. Solution, upgrade to 460hp turbo with ecu and fuel support.

Clutch died with new turbo. Not built to handle 400hp. Got a heavy duty one put on.

Since in both cases I was able to upgrade, theoretically no money was wasted.

Everything else is great. I love my Skyline :)

I've only had skylines over the last 5 years.. 2x R31, 1xHR31 (only for a few months), R33 GTS-T, and R32 GTS-T

Biggest problem was a crank angle sensor on my first R31.. and fuel pump on my current R32 (fuel pump was installed by me though and was aftermarket)..

Other than that, absolutely nothing. Pretty amazing, and why I've always bought Skylines :)

Only problem i've had was the stock fuel pump being basically dead, and the car running lean (not dangerously, but defintely on the way to getting there). Replaced that and so far it runs fine. I actually went a skyline over other imports/turbo cars in hope to get great reliablity, as I always drive my cars reasonably hard.

yeh im currently a ford bogan. yeh laught at me. i know i was an idiot for buyin the dumb thing in the first place. i was wondering how the skyline would be reliability wise with all the high revving n lots of boost etc. but you guys seem to rate them alright. cant wait to get mine. how do they handle flat changes? or dont they?

yeh im currently a ford bogan. i was wondering how the skyline would be reliability wise with all the high revving n lots of boost etc. QUOTE]

I dont own a skyline either mate but in regards to the (high reving) fest i asked my old man something similar and its not like the typical ford or holden engine... These are a performance engine so take alot more then f and h.

Even with my vl being the RB30 after a while of me really giving her a beating it drastically started to lose power but that wasent so much the engine it was really most things dying around it.

Mine's been perfect for a yeah in mostly stock form (changed turbo back zorst and cold air box). Had an issue with the fuel gauge reading empty way to early but it fixed itself and hasnt occurred since.

  • 1 year later...
Mine's been perfect for a yeah in mostly stock form (changed turbo back zorst and cold air box). Had an issue with the fuel gauge reading empty way to early but it fixed itself and hasnt occurred since.

Man I have had my car for six years when they were'nt soo popular and have never had any problems no oil leaks the car is damn strong. :happy:

1 motor 1 clutch and a couple of engine mount in my car but dare say motor was my own fault after putting the boost on 10 and not being tuned but all in all car cost me 16 owes me 21 after the motor and stuff and looks no better than day one haha but i still love it for the price what goes,handles and stops like 1 not much other than that its been great and pretty reliable other than my little mishap caused by myself

mine's been very reliable *knock on wood* and besides the normal services, its needed nothing.

one thing i noticed is the rb's are balanced pretty damn well. probably why they can take high revs/hard driving without issues. u can sit a glass of water on the motor while its idling and it hardly moves. try that on a commodore.

if ur going to push it hard...just make sure you look after your oil (restrictors, increased sump capacity and baffles) and you should be right to go... that's all i am aware of being a consistent issue if you are going to push it really hard (by the sounds of it you plan on thrashing it...excuse me if i am wrong)

...meh

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...