Jump to content
SAU Community

Recommended Posts

I have a mate who is selling a garret GT30r interally wastegated turbo. it has a .63 exhaust housing .7 front and a 560hp rating. I was wondering what power this would make and how laggy it would be on a rb25 that has fmic, powerfc, fuel pump and 550cc injetors as i am thinking about buying it.

thanks

Link to comment
https://www.sau.com.au/forums/topic/81287-gt30r-on-rb25det/
Share on other sites

I have a mate who is selling a garret GT30r interally wastegated turbo. it has a .63 exhaust housing .7 front and a 560hp rating. I was wondering what power this would  make and how laggy it would be on a rb25 that has fmic, powerfc, fuel pump and 550cc injetors as i am thinking about buying it.

thanks

I'm about to do the exact same thing

I have 96 model with fmic, full exhaust, intake, PowerFC, Fuel pump

Just got a VG30 exhaust housing (.63) to put on a brand new GT30 Compressor and core.

Should be at full boost at about 3500rpm.

All I need is injectors.

What kind of injectors do you have? Are they high or low impedance?

Link to comment
https://www.sau.com.au/forums/topic/81287-gt30r-on-rb25det/#findComment-1476900
Share on other sites

need more info is it modded internal...?  

if not 560hp turbo on a rb25det will be very laggy!  "est boost at 5-6rpm maybe".

a GT30 with a .63 rear housing will be on by 4000rpm

My advice would be aim for a .82 rear as a .63 will make it very "snappy" comnig onto boost which isnt good for traction

Matt, why do you have an RB25 :confused:

Link to comment
https://www.sau.com.au/forums/topic/81287-gt30r-on-rb25det/#findComment-1478856
Share on other sites

I had a GT30 o.82 rear on an RB20 and it had full boost by 4200rpm. Boost by 5 or 6 is bullshit. Id give the 0.63 a miss and go the 0.82; it'd be well suited to an RB25

saun- what mods do you have? my gt30 has a .63 rear and my rb20 doesn't have full boost that early

Link to comment
https://www.sau.com.au/forums/topic/81287-gt30r-on-rb25det/#findComment-1480949
Share on other sites

hey guys im also about to slap one onto my r33, i was told that it wouldnt be too laggy, about 4000rpm full boost.

if you think 4000 is too laggy... wow...

Mine with a .82 rear is all on by 4200. Stock head that is.

Still have nearly 4000rpm worth to use.

Link to comment
https://www.sau.com.au/forums/topic/81287-gt30r-on-rb25det/#findComment-1481207
Share on other sites

if its any help ive got one on my rb25 , starts making boost from2300/2500rpm and full boost by 3500rpm. so probably add another 500rpm for rb20 maybe.

Edit:

I have just read your gt30 thread.

.70 comp and .63 exhaust housing

That is why your making the power so early.For a moment there i thougt it was the .82 and i was wondering why you were making the power on average 500+rpm earlier than others with rb25.

Link to comment
https://www.sau.com.au/forums/topic/81287-gt30r-on-rb25det/#findComment-1481431
Share on other sites

saun- what mods do you have? my gt30 has a .63 rear and my rb20 doesn't have full boost that early

I had a Tial 35mm external wastegate plumbed into the modified standard manifold. Worked well too, but 0.63 would have been better on the RB20.

Link to comment
https://www.sau.com.au/forums/topic/81287-gt30r-on-rb25det/#findComment-1482181
Share on other sites

it should kick in about 4500rpm and ive seen people get over 260rwkw with the mods you have

my friend has a standard internal rb25 making 343rwkw with a gt35r/106.

its a huge rear housing for a 2.5l engine but it makes 25psi by 4500rpm. i suspect the gt30 with .63 will be at 25 psi by about 3500rpm

Link to comment
https://www.sau.com.au/forums/topic/81287-gt30r-on-rb25det/#findComment-1482253
Share on other sites

my friend has a standard internal rb25 making 343rwkw with a gt35r/106.

its a huge rear housing for a 2.5l engine but it makes 25psi by 4500rpm. i suspect the gt30 with .63 will be at 25 psi by about 3500rpm

Thats got to be harsh on the stock internals....

Link to comment
https://www.sau.com.au/forums/topic/81287-gt30r-on-rb25det/#findComment-1482423
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...