Jump to content
SAU Community

Drift1 racing Intercooler kits


Recommended Posts

  • Replies 104
  • Created
  • Last Reply

Top Posters In This Topic

Piping kit arrived in good condition and I installed it on friday the day I got it. I'm not sure but the kit may seem like it is more suited to R33 maybe? I had to drill out the mounting brackets to pull the intercooler in further so that the front reinforcement bumper would fit over, sits a bit lower than i expected over the thermo fan and a bit close to the top radiator hose. Also something that I realised with these kits is that they seem to pick up a bit of heat through there trip to the intake piping so i think they would benefit greatly from heat wrapping.

Just a bit of constructive critism. If anyone has any question in installing kits onto an R32 feel free to ask.

Cheers,

Link to comment
Share on other sites

Hey mate, I'm interested in the full kit for my R33.

Just making sure, is it $530 delivered, even to Perth?

Also, would you be able to send me one of those installation guides so I can have a look? I've pmed you my email.

Just got my car 2 weeks ago and haven't really pulled bits off a car before; would it be recommended that I get a pro to install it for me or is it simple enough for me to give it a go?

Link to comment
Share on other sites

yummy I dont have cooler instock.. Just jap has the cooler you need 600 x 300 x 76 mm with 3" inlet/outlet... YEs 350 for the piping delivered anywhere in aust..

Baz: When I installed the kit I lined up everything first before I installed it. Mark it all out, I planned everything before I did the chopping. This way I knew the kit would go together nicely.. But it did take be 10+ hrs to do it. So did you mark everything out first? did ou plan everything, made sure you cut the hole in the right spot so the piping would be as far away from the fan as possible etc... Maybe posting up some pics of your work? :cheers:

Link to comment
Share on other sites

have u got a pic of the cooler itself that u sell, because im lookin' at getting a kit for my r33. also before i purchase can someone send instructions to install it to [email protected]

so i can see what is involved, coz i ahve no idea how to fit it into the series 2 front bar . thanks

Link to comment
Share on other sites

hey mate, I'll send you the manual via email if I can.. I have been having trouble with my email :)... They manual will should you what to do..

I would recommend getting the cooler from just jap $5 cheaper and it is just the same as mine.. Besides I have no cooler left.. You need the 600 x 300 x 76 with 3" inlet outlet.

Link to comment
Share on other sites

  • 2 weeks later...
 Share




  • Similar Content

  • Latest Posts

    • My whp was 418whp and 518hp crank on 98 octane fuel. So decent numbers. 
    • Found a issue, after driving through torrential rain, the drivers side roof drain is blocked and some water ended up in the boot I've parked it up, stripped out the boot, and dried it out with a towel Initial fix was poking a big long cable tie down the drain to unblock it, then poured some hot water and detergent into it to flush out what I could, which now has it working, but I'm assuming it needs a good old fashioned proper "rogering" of the drain holes    Next step is waiting for the trombone cleaner that I just ordered from FleaBay next week Luckily nothing made it into the interior and it is all drying out nicely and the roof drains are working well enough for now I found the same issue with my old NB when I first got that, a couple of broken down leaves and some dirt was enough to block the drains, I did have a trombone cleaner back then, but I cannot find it anywhere, although, going of other times when I buy something to replace something I cannot find, the old one will probably turn up any minute now
    • Will look into the helical front diff thanks.  Sounds like everyone just says keep the rear as is. 👍🏻
    • R33 NA comes as rb25de or rb20e, so either of those, or r34 rb20de
    • I think the figures are pretty accurate as all my other cars are around the right hp readings as have done on multiple dynoes. However they are rwd cars so might mean the difference.    I am running every possible hks part also and a str exhaust … all new ecu. The mod list is endless. 😂 I’m ready for stroker and big turbo if I go that route. 
×
×
  • Create New...