Jump to content
SAU Community

Injectors are close to max!

Cristian

By Cristian,
in Engines & Forced Induction

 Share

Recommended Posts

Cristian Collaborator

Cristian

Posted
Posted

hey guys,

On the weekend I put the apexi PFC in my car, and tonight I got a turbosmart boost controller(mechanical). Im currently got it running 10-11psi and the injectors are at 81.1% they are close to max, and I want to run 12 psi.

What are the standard R33 gtst injector sizes?

Does anyone know if S6 RX7 injectors will fit stright in?

Link to comment
https://www.sau.com.au/forums/topic/82047-injectors-are-close-to-max/
Share on other sites
paulr33 Grand Master

paulr33

Posted
Posted

stockies are 370cc and theyll starting getting near 98% duty about 190rwkw - 200rwkw

as long as they dont sit on 100% for long duration, ie a few seconds its okay

just put it on graph mode with duty and take it for trash and make sure it doesnt flat line at the top. upto about 240rwkw ish is the "safe" limit where you can start to lean out and go bang (or get close to). i see 96% odd peak very occasionally and im only at 170rwkw so it varies but you should be fine, i run 12psi all the time

Dee 33 Community Regular

Dee 33

Posted
Posted

Larger pump and Malpassi here, pushing 240rwkw through standard injectors. Can't safely run more than 16psi though. My turbo wants more damnit :)

What's the point of a 460hp turbo if the car can't pump enough fuel to use the turbos potential? Money is the prob at the moment...

BHDave Grand Master

BHDave

Posted
Posted

S6 rx7 injectors can be made to fit with some minor mods to the bottom screen to allow them to fit into the rail. They are a slightly longer injector but still seal ok. Unfortunately they are only single pintle.

Mine has them in atm, though due to a niggling missfire issue i have no idea what duty they will be running at what max power.

edit: Forgot to mention that the s6 rx7 injectors use a denso plug (rather than a nissan plug) which can be picked up from any old fuel injector specialist. The plug needs to be notched to fit due to the large lip on the r33 rail.

DRFTR33 Contributor

DRFTR33

Posted
Posted

get an adjustable fuel pressure regulator

if you have a power fc you dont need to get a retune

all you have to do is measure your standard fuel pressure

fit your new reg and set your fuel pressure a certain percentage above standard

then go into your injector settings and take the same percentage off each injector

if you take your time and do your maths right you wont have a problem

GTRgeoff Grand Master

GTRgeoff

Posted
Posted
S6 rx7 injectors can be made to fit with some minor mods to the bottom screen to allow them to fit into the rail. They are a slightly longer injector but still seal ok. Unfortunately they are only single pintle.

Mine has them in atm, though due to a niggling missfire issue i have no idea what duty they will be running at what max power.

edit: Forgot to mention that the s6 rx7 injectors use a denso plug (rather than a nissan plug) which can be picked up from any old fuel injector specialist. The plug needs to be notched to fit due to the large lip on the r33 rail.

Wouldn't that be RB20 or 26 Dave?

  • 4 weeks later...
Bass Junky Grand Master

Bass Junky

Posted
Posted

I now need injectors to fit up my high flow.

I need to know what bolts up, and what are the best to use.

I don't want to use the bg suckers, as I would like more tuning resolution, as my car is a daily driver and needs to get resonable fuel economy and blah blah blah

Anywhoo.. think that I will make more than 250 and less than 300 rwkw.

What size should I use, I will never be upgrading from these injectors, as 250+ is quite enough for a rwd skyline.

I don't want to get the HKS injectors as you need a new rail and whatever, I'd prefer a 100% bolt in injector.

Car is an R34 GTT, high flow turbo. I'll run a FPR only to increase base pressure slightly as I understand that bigger injectors need slightly higher pressure to work properly.

All help appreciated.

BASS OUT

Sydneykid Grand Master

Sydneykid

Posted
Posted (edited)
I now need injectors to fit up my high flow.

I need to know what bolts up, and what are the best to use.

I don't want to use the bg suckers, as I would like more tuning resolution, as my car is a daily driver and needs to get resonable fuel economy and blah blah blah

Anywhoo..   think that I will make more than 250 and less than 300 rwkw.

What size should I use, I will never be upgrading from these injectors, as 250+ is quite enough for a rwd skyline.

I don't want to get the HKS injectors as you need a new rail and whatever, I'd prefer a 100% bolt in injector.

Car is an R34 GTT, high flow turbo.  I'll run a FPR only to increase base pressure slightly as I understand that bigger injectors need slightly higher pressure to work properly.

All help appreciated.

BASS OUT

Hi Bass, SARD make a straight fit injector for the Neo, I think they were rated at 460cc's but they flowed a bit more than that at standard pressure (36 psi above boost). They are on 85% duty at 265rwkw, that's at standard pressure. I did try them at 50 psi and the duty dropped to 70%, so there is plenty to go. I stayed at standard pressure though, as I am not keen on replacing all of the rubber hoses with braided ones. Rubber hoses, screw clamps and 50 psi doesn't sit too well with me.

:D cheers ;)

Edited by Sydneykid
mass_iv Grand Master

mass_iv

Posted
Posted

hey Bass, i just went through the same thing with my car i wanted a set of injectors that fit straight in, people were telling me that the nismo injectors are a straight bolt on, but when i went to powerplay imports they told me i need a new fuel rail so i changed my mind and went for the sard injectors with some colars, they fit straight in, but i got a r33 so i think its the same but not 100% sure.

Sydneykid Grand Master

Sydneykid

Posted
Posted
hey Bass, i just went through the same thing with my car i wanted a set of injectors that fit straight in, people were telling me that the nismo injectors are a straight bolt on, but when i went to powerplay imports they told me i need a new fuel rail so i changed my mind and went for the sard injectors with some colars, they fit straight in, but i got a r33 so i think its the same but not 100% sure.

RBInjectors.jpg

The injector on the left is top feed for an R34GTT RB25DET Neo

The injector in the middle is side feed for an R33GTST RB25DET

The injector on the right is top feed for an R32GTST RB20DET or R32 GTR RB26DETT.

Obviously they are physically not interchangeable.

:D cheers ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      WTB R34 GTR Guard Liners

      By Kinkstaah · Posted

      Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • itsmeyo
      WTB R34 GTR Guard Liners

      By itsmeyo · Posted

      Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • The Bogan
      NC MX5

      By The Bogan · Posted

      I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • Kinkstaah
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Kinkstaah · Posted

      You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • Dose Pipe Sutututu
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Dose Pipe Sutututu · Posted

      LOL.... you are correct there.
×
×
  • Create New...