Jump to content
SAU Community

Recommended Posts

yeah, jap safety feature which i think is mandatory over there... its on most imports.

Its not that annoying to me... kinda cool and ominous for the passengers! :thumbsup:

You can probably disable it - it will be hooked into the speedo somewhere.. might be complicated though because often if u have an alarm fitted its fitted into the central locking as well - is it really worth it?

Link to comment
https://www.sau.com.au/forums/topic/8336-door-locks/#findComment-120492
Share on other sites

  • 4 months later...

I want to re-enable mine too. The person that put the alarm in switched the central locking control over to that instead, which is much more annoying. Instead of waiting until you go over 25kph, it waits 3 minutes and then locks. And if you unlock/lock it again at any point before or after, it (a) won't lock after the 3 minutes if not already done so, and (B) won't unlock the car after you take the key out of the ignition.

I am now in the somewhat usual habit of just locking the doors after everyone is in the car and unlocking them when I stop. Unfortunately a lot of the time a n00ber passenger tries to get out before I remember to unlock his door and he/she wonders why they can't get out because they didn't lock the door.

Link to comment
https://www.sau.com.au/forums/topic/8336-door-locks/#findComment-360957
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok guys thank you very much. GCG highflow it is then 🙂 
    • forgot to mention that when it does this it does not kill the engine, but I have not kept the pedal down long enough to let it, as I see no reason to beat up on it as its got to be something simple, small and dumb causing this.  And as soon as I let off pedal, the engine returns to its normal super smooth operation and rpms re-stabilize quickly, once below 4k. 
    • neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
×
×
  • Create New...