Jump to content
SAU Community

Recommended Posts

  • Replies 60
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

How responsive is it compared to stock?

You have basically the same setup im going for except you're using 2560R's whereas im going for the HKS GT-SS's. I'm probably just gonna opt for 2xRB25 AFM's too.

You're running the stock fuel pump minus the low/high resistor right?

Overall a very nice result, grats!

You can keep your stock afms with the gtss's Kris unless you want to run huge boost ( above 1.2 bar ) .

In relation to results at WSID - LOL

First time at the drags, I had 3 runs. Two of them i absolutely buggered up. The first run bogged down with a 2.2 60 foot time. Runs were done at 15 pound boost, because my boost controller was playing up :angry:

I'll be back next week a fair bit earlier

In relation to results at WSID - LOL

First time at the drags, I had 3 runs. Two of them i absolutely buggered up. The first run bogged down with a 2.2 60 foot time. Runs were done at 15 pound boost, because my boost controller was playing up :angry:

I'll be back next week a fair bit earlier

:ohnoes:

Dont worry Tommy, sounds like you had some first time nerves. Will be good to see what the car can do.

In relation to results at WSID - LOL

First time at the drags, I had 3 runs. Two of them i absolutely buggered up. The first run bogged down with a 2.2 60 foot time. Runs were done at 15 pound boost, because my boost controller was playing up :angry:

I'll be back next week a fair bit earlier

what kind of times did you run? for the 2.2 60 was it bogging down or wheelspin?

Getting the launch right in a GTR with big turbos is a pain...such a fine line between sitting there smoking and bogging down.

I guess the 7000rpm launches might not work with these turbo's hey?

do you need to ride the clutch for a little bit in this instance?

12.7 for a first outing is a good start for sure.

I would have launched that first one at 5000 rpm MAX. And i really dont make decent boost until something like 6k or more. Next time I'll try to rev it out a bit more. I think i got there at about 7/730, so it really didnt give me much time to have many runs. Had absolutely no idea what i was doing, where i was going, etc.

I will be there next week. Hopefully boost controller issues will be sorted and ill be running 18-19 psi.

Either the turbos are just really big and laggy for my setup or something funny is going on ?

What gear is it that you don't see 15PSI till 6000RPM? My turbos are bigger than yours and I get full boost (1.3 kg) by about 4800RPM in anything above 2nd. I don't think I even get full boost in 1st though.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...