Jump to content
SAU Community

Recommended Posts

Im a major noob to wheels guys im upgrading to a series 3 R33 GTR soon and CBF reading through the 107 pages lol :yes: but basically the below link are the rims im looking to buy im after these in 18x10 - 10.5" if i can get them just wondering if anybody can tell me what offset i would need to get 275-285s under the ass without stupid camber or rolling guards etc they also need to clear my alcon brakes which are 315mm rear rotors and 4 spot calipers and and fronts are 356mm rotors with BIG 4 spot calipers im after diiiiiiiish also :whistling: Is this possible?

Cheers fellas

http://www.ebay.com.au/itm/170906816446?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649

A little help anybody??? Please.........

dont lower the car on anything you are likely to bend/kink the guard...

if you were close id help you out on sunday as i have a guard roller as well as all the other gear

yeh, you have to be real careful with that method... if it's just to lip the guards you can manage it without distorting them

Im a major noob to wheels guys im upgrading to a series 3 R33 GTR soon and CBF reading through the 107 pages lol :yes: but basically the below link are the rims im looking to buy im after these in 18x10 - 10.5" if i can get them just wondering if anybody can tell me what offset i would need to get 275-285s under the ass without stupid camber or rolling guards etc they also need to clear my alcon brakes which are 315mm rear rotors and 4 spot calipers and and fronts are 356mm rotors with BIG 4 spot calipers im after diiiiiiiish also :whistling: Is this possible?

Cheers fellas

http://www.ebay.com....984.m1423.l2649

A little help anybody??? Please.........

this one slipped through

nice wheels however it doesnt state what offset they are selling.....you would want to run an 18x10 (offset in the high teens) and you should be fine with that tyre size

I split the paint a tiny bit.

Was only able to get half a guard done and it was pretty hard I was unable to get the lip flush with the guard.

Rather the clogging up the offset thread if someone who knows what to do could message me that would be great either on here or mobile is 0408 257 613

Based on what exactly?

Kasko it's going to look tits brah :yes:

Based on another 33gtst with 9+20 all round. Front was little poke, rears were a little inset. That is why I went 10+30 on rears for that extra little poke..

Don't get me wrong, still looks mean, if you want same size all round - that offset would be the go.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
    • This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
×
×
  • Create New...