Wheel Sizes & Offsets For Skylines

[sleptema]

Just put the rims on only just fit, will be rolling the guards.

Question, how close are everyones tyres to the struts, looks a little to close???

Will 265 help that much??/

offset 40+

Thanks

No, the reason yours is so close to the strut is because you have an awful offset. I wouldn't run them until you get some spacers.. Chuck the stockies back on, roll all your guards, and push them out another 20mm or more (depending how mexican you want).

[1300]

Perfect, thanks for your help mate...

[1300]

.

Edited December 5, 2012 by 1300

[joeyjoejoejuniorshabadoo]

hubcentric BOLT ON spacers... but those rims may not have the capacity to run them, show us a photo of the inside of the rims before you go buying spacers.

It might work out cheaper to buy better fitting rims and sell them

[Granthem]

I know Meisters don't take bolt on spacers

[Frosty]

Just put the rims on only just fit, will be rolling the guards.

Question, how close are everyones tyres to the struts, looks a little to close???

Will 265 help that much??/

offset 40+

Thanks

want a lower offset or run a 5mm spacer

[Frosty]

I know Meisters don't take bolt on spacers

sif u buy meisters to run a spacer! you are not worthy

[TTR34]

Skyline model = R34GTT

Wheel diameter = 18"

Wheel width = 8"

Wheel offset = ?

Tyre size = 285/40/18

Just put some new rubber on.

They fit just.... can anyone point me in the direction of a good mobile guard roller?

Cheers

Edited December 9, 2012 by TTR34

[Manuel Kasko]

Where are you located??

I just did them myself and it was not hard at all

[TTR34]

Based in Brisbane, QLD

[Granthem]

Skyline model = R34GTT

Wheel diameter = 18"

Wheel width = 8"

Wheel offset = ?

Tyre size = 285/40/18

Just put some new rubber on.

They fit just.... can anyone point me in the direction of a good mobile guard roller?

Cheers

285's on an 8 inch rim?? Bit excessive there don't you think?

sif u buy meisters to run a spacer! you are not worthy

Haha - I know but ssssshhhhhh. When dealing with 20 inch Meisters the ability to pick sizes and offsets ceased in like 07 when they were discontinued. Now we all must deal and perserve with the choices others made in the first instance It's only my fronts I want to tease out a little more...

[TTR34]

285's on an 8 inch rim?? Bit excessive there don't you think?

Just a little..... hahaha

[1300]

want a lower offset or run a 5mm spacer

5mm spacers are on and have done a few kms, so far so good. Will check every now and again to see if there's any rubbing.

Thanks all for you help..

[B-rice]

anyone have a guard roller i can borrow?

[Manuel Kasko]

anyone have a guard roller i can borrow?

I got a mallet and a heat gun

Worked for me

[B-rice]

I got a mallet and a heat gun

Worked for me

I have a heavy hand ill rape it.

[B-rice]

shits me i cannot get the 10.5 with the wheels I want. what does a 10.5 +30 translate to with a 9.5 inch rim. What offset should i get to match the same flushness as a 10.5 +30 wheel.

Skyline model = R34 GTT

Wheel diameter = 18

Wheel width = 9.5 +22 fronts, 9.5 + ??????rears

[Frosty]

can run a 22 on the rear too if you like otherwise drop down to about +18 or a bit lower and you will be fine

[Manuel Kasko]

what does a 10.5 +30 translate to with a 9.5 inch rim. What offset should i get to match the same flushness as a 10.5 +30 wheel.

http://www.1010tires.com/WheelOffsetCalculator.asp

[TTR34]

Can direct me too a tried and tested guard roller in Brisbane?

Really need to roll these guards asap.