Jump to content
SAU Community

Recommended Posts

Don't panic.

I use regular unleaded in the jigger always. Rb20det, might not be making full power but it's certainly not pinging, that's what your right foot and the CAS are for.

I have found the regular starts much more easily than the PULP, just one touch and she's away. Same car on BP Ultimate has to crank away for quite a bit.

My only garage is a Matilda and their premium ain't too flash. Closest BP is 30mins away on the highway.

Link to comment
https://www.sau.com.au/forums/topic/85036-what-happens-if/#findComment-1542634
Share on other sites

ping ping!

in response to grigor... hmmmmmmm let's see:

extra $5per tank of petrol vs. $600-800 second-hand engine + labour + inconvenience + possibility of new problems with that engine

hmmmmmmmmm i might just go any put in what is was designed for myself

of course, its your car so best of luck with it

Link to comment
https://www.sau.com.au/forums/topic/85036-what-happens-if/#findComment-1542901
Share on other sites

I considered getting the car tuned for std. regular unleaded.

Then figured, $5 extra per tank.. bugger it. who cares.

I've considered throwing regular unleaded in it and watching the knock monitor to see how much of a difference it really makes. I would then pull ign. timing out until there is no longer knock.. It would be interestering. :D

Link to comment
https://www.sau.com.au/forums/topic/85036-what-happens-if/#findComment-1543063
Share on other sites

Come on guys!!! There is a difference between ping and knock.

How do you think your car was tuned in the first place? You advance up the spark until in pings then back it off a few degrees.

I don't have access to top quality fuel here in the sticks so I sacrifice a bit of power by winding back the spark.

What I said was don't panic. One tank of fuel won't kill it IF you use your right foot sensibly until it's been diluted with premium.

Link to comment
https://www.sau.com.au/forums/topic/85036-what-happens-if/#findComment-1543635
Share on other sites

my car pings going up hills with regular unleaded so i dont boost it at all on the rear occasions i have to use it.

if there is no other alternative to povo fuel i will just put in what i need to get to a servo that has PULP

Link to comment
https://www.sau.com.au/forums/topic/85036-what-happens-if/#findComment-1544581
Share on other sites

You should be OK if you drive the car conservatively, and your tuner has given you a street tune that allows for margin of error. I wouldn't go do a track day or the drags with it, though.

If you're using a piggyback or light tuning the factory ECU, the knock sensor and the learning functions should compensate.

If you're using a full aftermarket ECU (like a PowerFC), most of them don't have the learning function. It won't retard timing etc if the engine pings.

Occasional pinging isn't that bad (cars are engineered to sustain that kind of load occasionally) but if your car is constantly pinging (audible or not) then you're just causing undue stress on your pistons.

I'd use 91 to limp home if I was stranded in the middle of nowhere and couldn't get octane booster, but I'd put in as little as possible and be keeping an eye on my revs and throttle load.

Link to comment
https://www.sau.com.au/forums/topic/85036-what-happens-if/#findComment-1548389
Share on other sites

i did this in my stocky 33 and 32 gts-t's (only when i couldnt get premium).

I didnt have any problems. I didnt drive it hard.

If you need to tank up on 91 or 95 octane, please stay out of your boost range, otherwise your engine will knock if it is tuned for a specific fuel

Link to comment
https://www.sau.com.au/forums/topic/85036-what-happens-if/#findComment-1548685
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I had 3 counts over the last couple of weeks once where i got stranded at a jdm paint yard booking in some work. 2nd time was moving the car into the drive way for the inspection and the 3rd was during the inspection for the co2 leak test. Fix: 1st, car off for a hour and half disconnected battery 10mins 4th try car started 2nd, 5th try started 3rd, countless time starting disconnected battery dude was under the hood listening to the starting sequence fuel pump ect.   
    • This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
×
×
  • Create New...