Jump to content
SAU Community

Hitman / Race Solutions Dyno / Open Day! 25th Sept

race_solutions

By race_solutions,
in Events Archive

 Share

Recommended Posts

  • Replies 95
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

race_solutions Newbie

race_solutions

Posted
  • Author
Posted
I know this is gonna be funny.. But I really want to know what kw can my Type S make.. :)

Bring her down and find out! :O

Speak to Matt and he'll even be able to give you a few ideas to get the most out of her.

shonen Grand Master

shonen

Posted
Posted (edited)

Should be a good day........will be there...hopefully I can get the timing belt changed and fuel pump installed before then...

Maroun did my fmic for me, custom piping and all.......if you wanna see his handy work in metal fabrication then just let me know on the day. You wont be dissapointed......now where day heck did I leave that tub of metal polish ??? :P

Edited by shonen
Mintie Collaborator

Mintie

Posted
Posted

same for my car too...Maroun did the piping work on my car....dam it look so nice!!!

Should be a good day........will be there...hopefully I can get the timing belt changed and fuel pump installed before then...

Maroun did my fmic for me, custom piping and all.......if you wanna see his handy work in metal fabrication then just let me know on the day. You wont be dissapointed......now where day heck did I leave that tub of metal polish ??? :D

SAWAKITA Rising Star

SAWAKITA

Posted
Posted

Ok I'm in for this one, booking require? or just pay at the door?

anyone wanna meet up first and cruise there?

Bring her down and find out! ;)

Speak to Matt and he'll even be able to give you a few ideas to get the most out of her.

legend01 Experienced

legend01

Posted
Posted (edited)

Sounds good

Never done a dyno day but will come to watch to see what its like c all tha scmick cars

Edited by legend01
 Share
Go to topic listing


  • Latest Posts

    • RB25inside
      Compatible rear drive shafts R34 N/A?

      By RB25inside · Posted

      UPDATE: Yes the GSP Axles are compatible. I installed it on my R34 today and they are working a treat! Turns out that the S13, S14, S15, and 200 SX all used the same axles as the HR34, and ER34 NA models. Which is 2 bolt x 3 pairs.  
    • turbo76lx
      Torana Lx Gtr Hatch, Lots Of Pictures

      By turbo76lx · Posted

      Also build this EH ute with 370z motor and gearbox with a couple of turbos just for fun.  
    • turbo76lx
      Torana Lx Gtr Hatch, Lots Of Pictures

      By turbo76lx · Posted

      Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • joshuaho96
      Jacks that fit under GTR lips that can reach the subframe?

      By joshuaho96 · Posted

      Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
×
×
  • Create New...