Jump to content
SAU Community

Recommended Posts

Hey guys,

I got a prob with my front passenger rim on my 33. i thought the tyre somewhere had a leak as the tyre leaks air over about a month b4 i need to constantly reinflate it, so im always topping it up. i got it all checked out thinking it was the rubber, but they found a hairline crack in the actual rim.

I have 18" ROH Drift R's on the car, and i dont really want to replace that 1 rim which will prob cost 500 bucks, but it looks like i have no choice, it must be fixed or it will always continue to leak.

Is it possible to like get a tube put in just that wheel to fix it, as these type of wheels are tubeless..if thats the case id much rather pay 40 bucks than 500.

any advice would be appreciated

Link to comment
https://www.sau.com.au/forums/topic/86600-problem-with-rim/
Share on other sites

you can get it tubed at your local tyre place should be no dramas however i would be concerned of the safety of the rim itself if its cracked.

it could be unsafe and expand more or crack more at high speeds, that would be fatal, especially on the front

Link to comment
https://www.sau.com.au/forums/topic/86600-problem-with-rim/#findComment-1565224
Share on other sites

um iam pretty shore they dont make tubes for 16-17-18s coz they low profile, could be wrong about 16s but others iam shore off, just get some reall good glue n tank the tyre look 4 where air is comeing out n GLUE it, but i would fix or get new 1 if u wont i can get u these rim most likly.

Link to comment
https://www.sau.com.au/forums/topic/86600-problem-with-rim/#findComment-1569968
Share on other sites

i would advise against the tube idea even if you can find one for your wheel as they are not the safest things going around (excuse the punt)

as someone suggested best thing is to get it repaired by wheel repairers.

Link to comment
https://www.sau.com.au/forums/topic/86600-problem-with-rim/#findComment-1570307
Share on other sites

I got the wheel checked out at an ally repairer, the wheel is f***ed. the crack is too close to where the spoke meets the inner part of the rim so the only option is a new rim. but the rim is $280 so its not too bad..i was expecting them to be around 400-500 per rim.

And yes im still getting the 34. had it checked out and all looks good.

Link to comment
https://www.sau.com.au/forums/topic/86600-problem-with-rim/#findComment-1576025
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I ordered a GSP Front R/H Axle from here - https://justjap.com/products/gsp-premium-front-driveshaft-r-h-nissan-r32-r33-r34-skyline-gtr-stagea-4wd#description It lasted around a year before one of the boots blew out. I'm lowered, but I have GKTech roll center adjusters. One year seems a little premature. I think I'm going to spend the extra money on an OEM cv axle this time. This website - https://tfaspeed.com/collections/nissan-stagea-wgnc34-x-four-parts/products/nissan-stagea-awc34-260rs-rb26-right-front-axle-drive-assembly Makes it sound like the readily available OEM CV axle will only fit 11.1999 Stagea and up (mine is a 2.1997 S1). The JustJap listing didn't mention any years or anything for the GSP axle. Amayama shows '11.1999' and up as well for that part number. As well as 'plastic boot type'. See attached picture. So I guess my question is, does that axle (39100-23U60) really only fit S2 Stagea? It's the front driver side. If it does, I'd love to buy that instead of rolling the dice on another GSP. I've found that OEM one cheaper here: https://www.partsfornissans.com/oem-parts/nismo-jdm-r32-r33-r34-skyline-gtr-r32-gts4-right-front-axle-3910023u60 and here https://www.nissanparts.cc/oem-parts/nismo-shaft-ft-drive-3910023u60 Just a little confused because the JapSpeed listing for the GSP front driver axle doesn't mention any specific years or anything and it fit my S1 Stagea fine. So will 39100-23U60 fit my S1 Stagea even though technically it says '11.1999' and up? What would have changed? Thanks.  
    • Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • 75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
×
×
  • Create New...