Jump to content
SAU Community

Recommended Posts

good that you asked, because people use a high pressure water cleaner and then ask why there car is running like crap :)

hahaha, just like a guy I know got into his Impul's engine bay with a high pressure hose, and then found his windscreen wipers to run by themselves. :D

Driving through the middle of the city on a warm night with your wipers going isn't the greatest look.

Haha, after a very thorough wash of my car one night I found the back windscreen wiper going by itself. I just unplugged the motor and once it had dried out plugged it back in and all was sweet.

Anyway on-topic, the best way to clean the engine bay is with microfibre lint free cloths and lots of patience... A little degreaser used discreetely is useful as well.

hahahaha just the other night i was driving into the carwash place when i saw this guy washing his engine bay with a high pressure hose. once he tried to drive off it was running really rough and he didnt have a clue why..

its quality stuff to watch

This thread bring a question up for me, what if you have a vented bonnet and its raining heavily, Water could get anywhere in the engine bay, wouldn't it be similar to washing the engine bay without covering anything?

This thread bring a question up for me, what if you have a vented bonnet and its raining heavily, Water could get anywhere in the engine bay, wouldn't it be similar to washing the engine bay without covering anything?

Possibly. It would depend on the vent angle and size. If you were driving at the time its obviously far less likely given most vents face towards the back of the car, and any water that did make it in would probably evaporate when it hit the engine.

I put a fairly liberal amount of water on my engine last weekend and it was fine. Didnt blast the top of the motor too much and obviously kept direct pressure away from the fusebox and pod filter...was all good.

The biggest problem always seems to be getting the coil packs and spark plugs wet (judging by the number of "OMG!!!111 My car won't start post washing" posts).  Maybe cover sensentive areas with some plastic.

LOLOLOLOL thats what my friend (who has owned his skyline for 8years) did to my car which made me miss the show and shine remember? :P Bastards.. if only this thread was made back then

On the note of vented bonnets though, that means that all future car washes need to be done by hand... none of that servo 10minute job anymore???

Even if you foam up the car by hand you still gotta hose it down, so water still gets it. Maybe look out for certain vent styles that are directly above things like fuse box, spark plug cover etc...

I guess it could be a mod for people that have garages for their rides.

LOLOLOLOL thats what my friend (who has owned his skyline for 8years) did to my car which made me miss the show and shine remember? :P Bastards.. if only this thread was made back then

I'll make it up to you, one day I swear! I'm such a no-hoper :)

Although honestly, My engine(s) must have had a tighter seal around the top of the engine since I have never had that problem as much as you did :)

  • 2 years later...

I washed mine about a month ago at concord car wash, covered my pod filter with a plastic bag and used degreaser followed by high pressure rinse and hoped for the best. Luckily had no pronblems and drove off and its been fine.

With my previous car (mazda astina) washed it the same way and a shit load of water got into my spark plugs and was f**ked till i realised and got the water out.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've looked up the parts number (41011AL501). It's around $700 OEM. Usually our Infiniti G35 here in Canada have interchangeable parts with my Stagea but the parts number are not the same. I have looked around and it seems the JDM 2005 V35 Skyline (which is the same as our G35) has the same caliper but I cannot confirm. And I can't find a repair kit. The inner brake pads drags on the rotor, seems to be rusty piston. Thanks for the info by the way
    • This coupled with 6-9 speed autos with ridiculously short gearing is why these modern shitbox cars always seem so fast off the line. If it wasn't for those things, Raptors would not seem fast. The problem we have is there is a driveability gap between a more gentle take off and a wheelspinning sideways launch. The difference between ankle flex required to achieve one and ankle flex required to achieve the other is about 0.5°.
    • Yeah I think I'm also with the opposite here. It's 'hard to keep up with traffic' because in the real world I'm accelerating with 15% throttle and they are pinning it. It feels like I'm being an overt dickhead at anything above 15% throttle, so the car sounds like I'm being an overt dickhead to keep up with/get ahead of traffic when I'm really just trying to drive with traffic. There would be no issue 'keeping up with traffic' if we used the same level of throttle input/aggression to drive around. People really do just drive around with their foot nearly pinned in econoboxes.
    • To be fair it's the other way around. 300kw is boring in a modern Golf or BMW. They are so competent / well-engineered / devoid of emotion that you have to go stupid fast to feel anything. Whereas the <300kw RB still makes all the right noises and it feels good to drive. Can pull off at the lights with the turbo whooshing and the blow-off pssshing and feel like the coolest kid on the block. Just don't look to the side where you'll see the bored housewifes in their shitbox Yaris/Corolla/Camry that kept up because you didn't go fast at all
    • 300kW is so boring in a Skyline, you'll get spanked by someone's mum's Golf with Alibaba pipes, and an email tune.
×
×
  • Create New...