Jump to content
SAU Community

Recommended Posts

yes been very busy getting ready for Super Drift

oil cooler and relocator kit

radiator flushed and new top

new gauges

rb24 motor new tomei rings/ 1.2mm gasket / new bearings / 82mm tomei forged pistons

17x8,9 drif teks, running 235/45/17 wanli rear

new uras kit / paint

sparco seat

rear camber arms

rear strut bar

ummm thats off the top of my head anyway :S

fark man im so jealous. I cant even afford a f**king diff :(

What oil cooler did you get ? JustJap ?

running a hks 2530 on it still but got issue's somewhere power seems 'restricted' to around 180-190rwkw !!! :dry: the torque is noticeable but have to sort this out now that i have time :thumbsup:

the 2530 has made 236rwkw on a stock rb20 motor so would've though similar peak power with added low/midrange... hmmm

Heres some pictures of my laufiro as she sits at the moment. I bought the car for 1k in rough as guts condition so i wouldnt have to drive my done up s14 k's to work every day. After a few burnouts and a very cheap rb30, a few blown diffs etc i decided this was my next project.

The pictures shown are when the car still had the rb30e installed with nissan rocker cover, rb20e inlet, injectors and computer. It came out later that day.

Car is sitting in a shed waiting for the engine to be built. (NZ)

Specs when completed (should be about 6/8 months)

rb30det

r32 rb25de head

rb25det (r33 trans) - have rb20det at present but will be upgrading

gt3540r 0.86

tial external wastegate

ecr33 power fc modified to suit

q45 afm

sard 700cc gtr injectors with resistor pack

acl pistons

acl race bearings

gtr head gasket

performance springs valve springs

block decked to give perfect 8.5.1 compression

I have most of the parts together here now, just waiting for my mechanic mate to get the motivation to start the engine build.

17x8.5 30 offset rear Racing Sparco rims

17.8 35 offset front

The body is an 89 cefiro that was as rough as guts when i got it. The laurel front was off a friends parts car and the whole car has been sprayed in my garage. The engine was installed as a friends boss had a cheap one and the rb20e wasnt doing its job spinning tyres.

I pick up some custom laufiro guards in a week or so time so that should complete the exterior. I dont plan on fancy kits etc as they are likely to get damaged and ruin the drivability of the car.

It should be good for 320+ kws when completed

post-21312-1149580452.jpg

post-21312-1149580497.jpg

Edited by SirRacer
  • Like 1
sir racer were can i get some of those lofiro gards can you please post a pick of those because im looking at doing a lofiro convertion aswell

they were custom made by someone in auckland nz by combining both cefiro and laurel guards together. apparently its a shit of a job so will cost around 600+ easily

i have thought about getting a fibreglass copy made but dont really want to fork out 400 to get them copied then loose my individuality. im in NZ anyway so that prohibits you getting a copy of mine

Thanks yeah I love it more than anything :dry: All work carried out in Japan.. Fronts are aftermarket flares that have been smoothed over. I'm guessing the rears are the same with the added complication of the door.. but yes large quantities of bog is involved :)

Edited by Drift_Limo

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
×
×
  • Create New...