Jump to content
SAU Community

Late 1996 Series 2 R33 Gtst (damage) For Sale

hkg1980
 Share

Recommended Posts

hkg1980 Enthusiast

hkg1980

Posted
Posted

Here is a 1996 Series 2 R33 Gtst with Manual Gearbox with roll over damage.

Will sale the whole car with all running gear with a complete body shape for repair or I can sale all the car as part (Wrecking)

Car with new compliance plate which complied on FEB 2005

Colour:Black

Interest call 0411660897

No photo avaliable on web unless call me and give me your e-mail address directly!!

Slide Grand Master

Slide

Posted
Posted (edited)

oops double post

free bump for advertising providing you dont sell my rio to anyone else :D

Edited by Slide
AlexCim Grand Master

AlexCim

Posted
Posted

Looking for

clutch master cylinder

slave cylinder

clutch pedal set (every bolt/part from master cylinder back into the cabin)

handbrake lever + assembly (not the cable though, just the incabin assembly)

Give me a price on these parts, as i want them ASAP :)

PM please

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Slight brake pedal stutter after new pads

      By MBS206 · Posted

      Jack the back of the car up, pull that wheel off, pull that sensor out, and put a bore scope into the hole to inspect the outer casing, see if anything looks damaged before you pull the whole thing apart.
    • PranK
      Slight brake pedal stutter after new pads

      By PranK · Posted

      Ergh... So I pulled the speed sensor out again and the tip was shiny so I think it's rubbing the bearing. The bearing contains the magnets for the speed sensor so I think when the first sensor broke it damaged the magnet ring on the bearing.  This is just a Google image, but there is a hole going to the bearing. So when the tip broke off the old sensor I'm guessing it fouled the bearing... As the magnet is only protected by a plastic cover it would be easy to damage it. So I guess I'm doing a bearing again.   
    • GTSBoy
      Unknown sound similar to BOV on positive boost with partial throttle RB26

      By GTSBoy · Posted

      My thinking is that if the O2 sensor is shot then your entire above described experience is pure placebo.
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      Here is the mess that I made. That filler there was successful in filling dents in that area. But in the middle area. I can feel dents. And I've gone ocer it multiple times with filler. And the filler is no longer there because i accidently sanded it away. I've chased my tail on this job but this is something else lol. So I'm gonna attempt filler one more time and if it doesn't work I'll just high fill primer the door and see where the issues are because guidecoat is of no use atm.
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      Ok, so I think I sort of figured out where I went wrong. So I definitely overthinked it, and I over sanded, which is probably a large part of the problem. to fix it, I ended up tapping some spots that were likely to be high, made them low, filled them in, and I tackled small sections at a time, and it feels a lot better.    I think what confused me as well is you have the bare metal, and some spots darker and some are lighter, and when I run my finger across it, it' would feel like it's a low spot, but I think it's just a transition in different texture from metal to body filler.    When your finger's sliding on the body filler, and crosses over to the bare metal, going back and forth, it feels like it's a low spot. So I kept putting filler there and sanding, but I think it was just a transition in texture, nothing to do with the low or high spot. But the panel's feels a lot better, and I'm just going to end up priming it, and then I'll block it after with guide coat.   Ended up wasting just about all of my filler on this damn door lol  
×
×
  • Create New...