Jump to content
SAU Community

Recommended Posts

ohk just had my new alarm installed yesterday... however the remote start keeps trying to start the car after it turns it on

i was told that i will have to wrapp te wire around one of the coil packs and it would fit it.. and i did this... however the problem is still happening

does anyone have any ideas?

-Ruffels

Link to comment
https://www.sau.com.au/forums/topic/88352-remote-start-keeps-trying/
Share on other sites

mm i didnt think so

i was told that the electromagnetic field produced from the coilpacks would induce a current (which makes sence, hence flux) in the wire and indicate to the alarm that the engine is on and to disscontine trying to start the car

however a friend who installed his own alarm in his cressida said he connected his remote start to his tacho wire

i am thoughrly confused right about now

and im just wondering if anyone with an r33 has remote start as part of thier alarm.. and if so how they overcame this

-Ruffels

R33 is behind the dash - yel/red on a S1 not sure what it is on a S2. do you own a multimeter and KNOW how to use it?

if no - pay a shop. you can wipe out a LOT of electrics on that car if you are not careful teh ECU bing one of them.

yup... i own a multimeter and i know how to use it :)

i cant be f***'d pulling the dash out so hopefully it comes down in the section of the loom that is accessable from under the steering collum

so i'll keep my eye out for a yellow and red wire cheers

-Ruffels

you dont have to drop the dash just to get to the tacho sense wire, the easiest solution would be to run the wire into the passengers kick trim and connect it to the ECU, from memory it is pin 7 from the ECU but i would check that first

Google is your friend, do a search for R33 ECU pinouts and im sure you will find the correct wire

Its obviously keeps tryin to start because the alarm isnt sensing any input to stop the module from cranking

you were able with the old style remote start alarms to wrap the sense wire around one of the ignition leads goin to the coil but this cant b done with the new style alarms

ohk... all fixed

thanks to Kris (krsysui) i managed to locate the tacho wire from the ECU

for all r33 boys its yellow with blue stripe.. both S1 and S2 so i dont know where you got the idea of yellow/red chris rogers... but thanks anyways

i took the wire and spliced into the tacho wire and the problem is now fixed :P

thanks all

-Ruffels

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • BOVs do have a purpose, if you ever log pressure before and after the throttle body, you will see a spike pre throttle on lift off from a WOT condition. Enough to bend throttle blades / damage e-throttle motors or simple assist in blowing off cooler pipes. FWIW, the above on really applies to those running at least 2 bar of boost. OP shouldn't have an issue, on the other hand, here are some videos of my shit box over a decade ago with some succulent dose with the airbox on and off. That shit box is unrecognisable these days 🫠    
    • I've tried all different combinations of BOVs/ no BOV and stock bypass valves over the years, on gear changes the stock bypass valve seems to get the car back on boost quicker because in part the turbos wheel speed isn't being slowed down by reversion, although they have issues holding boost much over the stock setting. Most aftermarket BOVs you can adjust the spring, tighter will make it open later and close sooner, but in my experience it'll cause a bit of flutter at low load/rpm anyway. I've also got some input into this whole no bov causing turbo wear, never had an issue on any on my turbos HOWEVER, I got my R33 GTST with 200k kms on it, with from what I can see still has the original turbo, no lateral shaft play but has about 4-5mm of play in and out which to me seems like a worn thrust bearing from years (100-150k kms?) of turbo flutter running no bov, so maybe there is some truth to it in the long run. But that'll never stop me loving the Stutututu while I have the car.   OP just wants to know if he can run a atmo vented BOV with no major issues and the answer is YES, plenty of people do it, there's no harm in installing it and seeing how it runs before spending $$$ on an aftermarket ecu, last time I bought a Nistune it was $2400 for install and a tune , unsure of todays prices but you get me. Crazy money to spend just to fix the minor inconvenience of stalling that can be overcome by letting the revs come down to near idle before putting the clutch in or a little bit of throttle to avoid it. You're better off leaving the ecu and tune for after a bigger turbo/injectors have been installed to take full advantage of the tune and get your moneys worth.   Let OP have his Whoosh sound without trying to break his bank haha
    • I see you missed the rest of the conversation where they have benefits, but nothing to do with avoiding breaking turbos, which is what the aftermarket BOV made all the fan boys, tuners, and modders believe was the only purpose for them...
    • But they do so for the other reasons to have a compressor bypass. It's in the name.
×
×
  • Create New...