Jump to content
SAU Community

Recommended Posts

Hi all,

I have the following parts available

TOMEI RB26 Upper Oil Gallery Restrictor - Brand New $40

Brand New Genuine Nissan Head Gasket for RB26DETT SOLD

R33 GTS-T Factory Springs (x4) $40

R33 GTR Timing Belt (approx 30,000km's old) $30

R33 GTR Factory Dump Pipes (x2) $Offers?

R33 GTR Factory Adjustable Front Strut Brace $120

R33 GTR RB26 Factory Head Bolts $OFFERS?

RB26DETT Factory "Twin Turbo" Pipe $100

ttpipe.jpg

Located in Sydney

Post, Pm or email me nick @ skylinesaustralia.com

Link to comment
https://www.sau.com.au/forums/topic/88531-loads-of-gtr-parts-for-sale/
Share on other sites

  • Replies 73
  • Created
  • Last Reply

Top Posters In This Topic

Hey are 32 and 33 GTR turbos the same?

would you do a swap plus cash?

Swap for?

I have just upgraded turbo's so I dont need these anymore.

Hope this clarifies

Thanks

Nick

I have 32GTR turbos but on the net they say t28 but when i compare it to a S13 turbo its exactly the same it says M24 on the front cover.So i'm guessing they mean 33 gtr's have t28s so i was asking if you would like to swap

PM me if you would like to do swap plus cash

I have 32GTR turbos but on the net they say t28 but when i compare it to a S13 turbo its exactly the same it says M24 on the front cover.So i'm guessing they mean 33 gtr's have t28s so i was asking if you would like to swap

PM me if you would like to do swap plus cash

Sorry mate, but I have removed these turbos from my GTR and replaced them with HKS turbos so I have no need for these turbos any longer.

I will pass on your offer, thanks anyway

Hi there,

Does the clear Cam Cover have 26 printed on it? Or has nothing? I might want to fit it on my 32t. Can you send me a pic to [email protected]

thanks :P

Hi there,

Does the clear Cam Cover have 26 printed on it? Or has nothing? I might want to fit it on my 32t. Can you send me a pic to [email protected]

thanks :)

Hi Mat, the cover is a genuine Trust/Greddy brand new part, and has RB26 on the front of it.

I dont have a photo unfortuantely.

Cheers,

Nick

will you sell stock cam timing belt cover by itself or only with camshaft cover aswell? I only need the cam timing belt cover but don't want a clear trust one.

Cheers

Jamie

will you sell stock cam timing belt cover by itself or only with camshaft cover aswell? I only need the cam timing belt cover but don't want a clear trust one.

Cheers

Jamie

Jamie, will consider it pending your offer

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...