Jump to content
SAU Community

Recommended Posts

The RED one is a NICS engine. It is the earlier of the 2. And has less power.

The NICS has 2 inlet runners per cylinder, 1 of which has a butterfly that opens and closes depending on the requirements. These tend to jam, so that the engine is either terrific down low and crap up high, or crap down low and terrific up high.

The heads are different, but interchangeable (I know the inlet manifolds are not interchangeable).

That's my limit. Anyone else add or correct.

The RED one is a NICS engine.

Greg you are correct in your description of the early NICS engines, but there was also a red-top ECCS version of the RB20DET which was used in HR31's from about mid 1987. The red ECCS uses a very similar manifold setup to the R32 silver type - in fact it looks largely identical, but there might be detail differences. The (rough) power output of the three types is:

NICS - 140kW

red ECCS - 150kW

silver ECCS - 160kW

Probably the main differences between the R32 ECCS and the R31 ECCS is that the R32 used a ball-bearing turbo (R31 used plain bearing) plus the R32 had a more refined engine management system. That said there are probably internal detail differences, but I haven't compared them.

To complicate matters somewhat, the silver ECCS engine was also used in some late model Cefiro's, but for some reason the Cefiro version used a plain bearing turbo (like R31's) - well that's what I'm lead to believe, anyway.

Nics and red eccs are both 12 port heads and silver is 6. The red eccs actually also has the same inlet butterflies as the nics but has a 6 runner manifold like the silver.

There are many minor differences between the silver and red eccs like injector sizing, impedance, fuel rails, throttle body sizing, sensors, ecu etc. Do a search as it was covered very recently.

In what way? I have a red eccs in the GTS-R and its 100% a 12 porter and it 100% had the butterflies as I removed them.

Its not uncommon for people with red top eccs engines to ditch the butterflies and manifold and use the silver top gear instead. If the head was never removed they would never assume it was a 12 porter.

I myself never knew it had 12 ports untill the manifold was removed.

The below pics are butterflies and a head from a GTS-R which has a red eccs as standard.

post-7700-1127542397.jpg

post-7700-1127542438.jpg

In what way? I have a red eccs in the GTS-R and its 100% a 12 porter and it 100% had the butterflies as I removed them.

Its not uncommon for people with red top eccs engines to ditch the butterflies and manifold and use the silver top gear instead. If the head was never removed they would never assume it was a 12 porter.

I myself never knew it had 12 ports untill the manifold was removed.

The below pics are butterflies and a head from a GTS-R which has a red eccs as standard.

You are exactly right Jayson.I too had the head removed from my old red top eccs Rb20det-r and it looks exactly the same as your picture(12 ports),even though it had the 6 runners on the plenum.Cheapest power upgrade for top end power has to be to remove the butterflies.Shit job though.

Does someone have a picture of a silver top Rb20 head,i would like to see the difference.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...