Jump to content
SAU Community

Recommended Posts

Just wondering, someone wants to buy the shell of my car with the driveline, but without wheels and suspension.

How do you get that towed?

I'm assuming you'd have to keep it on some sort of stand?

And you'd need a special company to do the towing?

Any help is appreciated, thanks.

Link to comment
https://www.sau.com.au/forums/topic/91419-how-do-you-towdeliver-a-shell/
Share on other sites

Hey dark,

Towing body shells is no issue for me, as long as you and the buyer don't mind the underbody of the car getting scratched from dragging onto the truck and sliding it off at the other end. Mind you it doesn't actually do any structural harm to the underbody...

Call me when you ready to discuss this further 0419877437..

Cheers

Hey dark,

Towing body shells is no issue for me, as long as you and the buyer don't mind the underbody of the car getting scratched from dragging onto the truck and sliding it off at the other end. Mind you it doesn't actually do any structural harm to the underbody...

Call me when you ready to discuss this further 0419877437..

Cheers

Shouldn't be an issue.

I'll give you a call tomorrow morning.

Thanks Jack.

Hey JAGR33 do you have a way to move em without scratching? dolly wheels or something?  Its a problem I seem to have too often, trying to move a car without wheels :(

Maybe tie the car to some packing crates (the ones for use with forklifts)..?

i might give that a go

Hey JAGR33 do you have a way to move em without scratching? dolly wheels or something?  Its a problem I seem to have too often, trying to move a car without wheels :angry:

Duncan, your right, the proper way to drag it onto the truck is to use what they call 'ambulance wheels', but only panel shops have usually got them... I don't have them coz they are big and bulky which means I can't store them anywhere on the track and the main reason being I hardly ever need them...

dark, palletts usually work but sometimes get caught on the end of the tray when dragging the car up, resulting in the car sliding onto the tray and the crate staying on the ground. Once you get it over the little lip on the tray it's all good, although getting it off at the other end can be a problem aswell....

The way id go about it

* Buy (steal) a 2 tonne pallet (i buy ~30 at a time for ~$12 each 2nd hand refurbished)

* Put car on jackstands and strip as needed

* Put pallet under the car and lower it on

* Get a flatbed with a forky (the same as what bricks are delivered on) to come and fork the car onto the flatbed

* Deliver as needed

Or.. the cheap ass method...drag it on as suggested above...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks Dose.....    I appreciate it!!
    • I'll probably be putting the shit box back on the dyno again soon, I want to dial in the closed loop boost control properly. I'll have a camera facing the car/motor for fun too. Just note, there are essentially 3x 10AN inlets going into the catch can and 1x going back to the intake pipe. Most of the time the catch can "return" to the sump actually is the crank case breather, pushing air out.
    • I have the R3C with a Nismo slave and by no means does it behave like a stocker, it ain’t THAT bad. On take off just give a bit more throttle than you would say a coppermix and it’s fine. It will not slip though.   
    • Okay. Final round of testing done. Got a friend to hook up a fancy scanner to the car and we also ran some compression and leakdown tests, she is healthy.  The MAF was definitely the culprit. So for future reference anyone with similar issues that find this thread. I suggest the following steps, in order of affordability:   Check your spark plugs for any fouling, replace plugs if they are bad or re adjust the gaps making it narrower (0.8mm would be good). Check every coil's resistance with a multimeter. It can be done by probing the IB and G pins on the coil pack. Resistance should be around 1.4 (+/- 0.1) Ohms Check the MAF. If you have Nissan connect or a good scanner with the 14 adapter it should allow you to see the voltage on the MAF reading should be around 1.1 - 1.2V when car is idling. But if you don't, buy a new MAF from Amazon and test, then return it. (For instance, I got a Chinese one for $40 that was reporting 1.3v on idle). If you still have scanner, you can run tests on the injectors to see if they are working, just remember to unplug the fuel pump fuse/relay and have no pressure on the line. Then listen for the noises that the injectors make. Clean/replace injectors as needed. Once you find the issue and fix, order thousands of dollars worth of OEM parts to refresh unrelated things (Optional)   PS: Thanks to the absolute legends of this forum for the responses and help to someone that went a bit over their head. (me)
    • Ha ha ha, so they stopped the bearings spinning on the one you want, but then decided the crank hub should slip instead 😛   Stick to RB, at least you can work on it yourself. And now it doesn't smell of vapour   Also I still believe there's a chance your new flap doesn't "pop", as even though the engine might breath hard, it has a direct path with no restriction to the inlet, which when on boost should pull a bit of suction for you. If you do get pressure in the catch can id be very intrigued. Time to put a boost gauge on it, and a session at the track, then solid cover your vent and do another session
×
×
  • Create New...