Jump to content
SAU Community

Recommended Posts

Who is running the stock GTT turbo at this sort of boost?

How long have you been running it?

I got my GTT tuned recently and they tuned it with this boost. I figure I can always drop it down a bit but it might mess around with my tune?

I would probably just leave it up at what it is, if its reasonably safe.

Edited by noise
Link to comment
https://www.sau.com.au/forums/topic/93394-gtt-stock-turbo-at-13-14psi-all-day/
Share on other sites

I deliberately tried one at 12 psi, lasted 4 laps (1 warm up and 3 fast) at Oran.

Ben's lasted 5 laps at Wakefield at 12 psi.

I warned a guy running 12 psi that it would happen to him.

He reckoned it wouldn't 'cause he never drives on the circuit

His got his ceramic in the cat disease driving hard up the hill from the Mooney Mooney bridge on the F3.

Cost him a new turbo and a bottle of JD (he lost the bet :rolleyes: ).

tick....tick......tick

:P cheers :(

Edited by Sydneykid

Uh, this might sound like a really odd question.

But if you blew your exhaust turbine wheel pretty bad, so that it wouldnt spin the compressor any more. Then effectivly, the car will always be in VAC, will the ECU still be able to run the car correctly at say 5000 when it would normally be in +ve pressure?

I can get it at 5000 in vac, just doing down a hill in second. But... i dont know if thats the same?

Essentially, if turbo breaks, can the car still run/be driven normally?

ALSO, does the cat get damaged much when blade peices go into it?

Edited by AlexCim
Uh, this might sound like a really odd question.

But if you blew your exhaust turbine wheel pretty bad, so that it wouldnt spin the compressor any more. Then effectivly, the car will always be in VAC, will the ECU still be able to run the car correctly at say 5000 when it would normally be in +ve pressure?

I can get it at 5000 in vac, just doing down a hill in second. But... i dont know if thats the same?

Essentially, if turbo breaks, can the car still run/be driven normally?

ALSO, does the cat get damaged much when blade peices go into it?

In the examples above, all 3 guys drove their car home without a problem.

:rolleyes: cheers :P

Yeah, my compressor wheel still spins with the air going through it, but it's rubbing on the housing, and it squeels like a banshee!

Still drives though. Just doesn't do it in any sort of hurry!

Is the R34 turbo weaker than the R33? I was going to get my dyno tune (on my 33) done at 12psi so atleast the tune would be good up to there..then back it off to 10psi for most use. Maybe I'll go back to 10psi then too be safe as maybe on the dyno at 12psi the turbo will blow up :rolleyes:

Thanks for all the replies guys.

The reason I ask is because a friend of mine ran a stock r33 turbo for 6 months on about 15psi with no problems at all.

And I have spoken to a few people around the place who run them on about 13-14 daily with no problems.

But you certainly cant ignore the broken turbos in this thread.

If my car is tuned for 14 will it run badly if i drop it down to 10 with my avcr? I might run it on 10 for daily and pop it back up on weekends... haha

there's another factor to consider.

14 psi on a stock computer ain't as much as a problem as 14 psi on a PFC running timing and 12.0 AFR.

Lots of timing and lean ratios, = HOT gas.

The ceramic turbine gets too hot which makes it delaminate from the shaft.

Hence, cooler exhaust gas, less chance of blowing turbo.

Not likely I wouldn't think on a single turbo.

When you blow the wheel off, the are normally at WOT and by the time the thing blows and the you realise, the thing is already embedded in your cat!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...