Jump to content
SAU Community

Recommended Posts

  • 4 months later...
  • 2 weeks later...

I was having the problem with the hot/cold mixing actuator not working. When I got down in the passengers footwell I tried to move the rod by hand but it was completely stuck. After a bit of stuffing around I got the part with the motor that controls the actuator out and I started playing with it. When the motor was not connected to the other little cogs, it would run constantly. Also the cogs would turn freely on their own, however put them together and they wouldn't budge. Also I think I may have damaged the motor because after a while it wouldn't run at all.

Any ideas of what's going on?

  • 2 weeks later...

Is it possible to have the locations of all the temp sensors. My Outside, Inside and intake sensor are reporting -21.6 whatever which means it isnt connected or is dead, but as most people have noticed the downloadable workshop manaul's pictures are too monochromatic to define exactly where they are.

I know that the Inside sensor is below the ashtray and from what i remember it looks like a funnel, or is this an airhose for a gremlim inside the dash of my car...

Widebody180: Apparently the majority of motor faults is broken solder points inside the motor box. I saw a tutoral on how to fix it, and you to go through where your sterio and A/C controls are to get to it without removing the entire dash.

Cheers!

Paul

Edited by Helious
  • 2 weeks later...
  • 1 month later...

Hi All ,

I have a 32gtr with the a/c not getting cold at all

i have done all the checks and all sensors temps are ok , all door and flaps work but still no a/c

Tried the FC option still no a/c

Had system regased - still no a/c

The compresor is not pulling in at all . the only way to make it pull in is to by pass the relay- then it will get cold

Any ideas as to where to look for the problem ????

Will be getting hot soon so would like it to work!!!!

  • 2 weeks later...

i have a r32 gts t

my a/c works but not 100% it is not as cold as i would like but i can live with it. i had to disconnect the hotwater hoses coming into the box. From what i have seen the flap is not working. My main problem though is when i turn on the a/c it does not throttle up the car so it will shut off.

my readings are -21, 25, -26, 27 and this is in the night.

questions though

1. i do not need the heater but will the heater flap open caz it not to be as cold as it should

2. does these readings show that any sensors are gone bad? if so whats the fix

thanx in advance

  • 2 weeks later...

Fault Codes

20 - all is normal

21 - outside air sensor

22 - Inside air sensor

23 - Water temperature sensor

24 - Intake temperature sensor

25 - Sunload sensor (small sensor on the left hand side of the dashboard near the windscreen)

26 - PBR

27 - Refrigerant temperature sensor

you fix sensors by replacing them. you add resistors if they are out of calibration - or - you want to over ride them.

Fault Codes

20 - all is normal

21 - outside air sensor

22 - Inside air sensor

23 - Water temperature sensor

24 - Intake temperature sensor

25 - Sunload sensor (small sensor on the left hand side of the dashboard near the windscreen)

26 - PBR

27 - Refrigerant temperature sensor

you fix sensors by replacing them. you add resistors if they are out of calibration - or - you want to over ride them.

so if my faults are21, 25, 26, 27 how do i know if they are gone bad or need calibration? or will i have to test the temp.?

  • 1 month later...

Hi all awesome thread handy info cheers guys, my ac prob is abit diff.

All the sensors and that seem to be swt but the ac blows ambient air and when I turn it on and off it always resets and goes back to 25 degrees. Anyone had a similar prob? Or able to help?

Thanks Corin

Hi all awesome thread handy info cheers guys, my ac prob is abit diff.

All the sensors and that seem to be swt but the ac blows ambient air and when I turn it on and off it always resets and goes back to 25 degrees. Anyone had a similar prob? Or able to help?

Thanks Corin

this is normal mate

Hey tested it on my mate 32 yesti and his one doesn't reset when u turn the ignition off, but it does when u disconnect the bat, anyways looks like I'll have to get an auto sparky to have a look

SMIK YER!!!1 this worked on my car , cost me nothing for the resistors too hahaha i got 2 and they were 6c each but the chick said they were on sale 1c each hahah so she just gave me my 5c back , went to the parking lot put the 2k resistor in and WOW cold freakin air ! love it , thanks heaps for everyones input

Franco

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
    • It's TWO steering wheels actually. 😛 one for each hand They are wheels, and they steer!
×
×
  • Create New...