Jump to content
SAU Community

Phillip Island Track Day

pomejo

By pomejo,
in Archived Events

 Share

Recommended Posts

Al Grand Master

Al

Posted
Posted

:( Not what i wanted to see :(

Hope you are OK. More justification of my decision to stay off the track, after i just completed fixing the car up from a very similar accident, at Calder Park.

All the best, i'm sure she will be better than b4.

ferni Grand Master

ferni

Posted
Posted
post-22998-1134629134.jpgpost-22998-1134629188.jpgi had a great day untill i crashed. down the back on the big s bend i just cliped the dirt with the back wheel and  spun then ended up hiting the tire wall  and  smashed the back of the car in

:( :( :( I didn't know dude, i left early - such a sad sight to see :( how fast wer eyou going when you hit the dirt/came off?

How much $ is it to fix it? Hope it works out for you dude :(

Bec Grand Master

Bec

Posted
Posted

OUCH Jo!!! :)

I had to leave early so I missed this, was very sad to hear when Chris let me know - even worse to see the photos.

I know everyones probly said it already and it probly doesn't make you feel any better - but at least you're OK, it could have been worse.

Hope you get it all fixed up without too much of a financial dent and hope to see you around again soon. Come sink some beers with us at one of the monthly meetings when you get a chance.

Cheers.

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      S1 rb25/s14 starting problem

      By Duncan · Posted

      Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...