Jump to content
SAU Community

Recommended Posts

Hi Jim,

I find these results amazing, 20awkw is a substantial increase!

I have booked my final tune with crd for next week...I will post my results here for everyones perusal.

Regards,

Marko.

Hey Guys,

Here is dyno sheet of a R33 GTR with a new engine we built with R34 N1 turbochargers with before and after of 98 and 100 octane shell fuel.

Car is used for circuit only.

CRD

  • 2 weeks later...
ive had my safc tuned for 98 octane.. if i use this extreme stuff would i REALLY need a retune?

Only if you rev the engine out, or value your pistons' life spans.

The fact that higher RON level means you can run more timing isn't as important for the retune, but the fact that its oxygenated means your engine will run lean comparable to your 98RON tune is why your current setup may not be good for the engine.

If you've got it tuned close to the edge on 0% ethanol fuel, the E5 Optimax Extreme might push it to a point where you get detonation.

This is big I actually calculated 41 extra four wkw for extra 2 octane points. Must have had more timing and maybe more boost added to do this?

We did same on S15 yesterday and made almost 20rwkw with a bit more boost and timing.

There is a question mark with the Ethanol in it effecting injector seals as well as early model injector design and electrolysis. But hey I am going to use it and guess it should be ok or they would not release it, or are we all test pilots?

well, i had a sip of it yesterday and it tastes no where near as good as bp ultimate. true.

It certainly looks like a good option for race use. Much cheaper than the options from elf etc.

well, i had a sip of it yesterday and it tastes no where near as good as bp ultimate. true.

It certainly looks like a good option for race use. Much cheaper than the options from elf etc.

full tune and comparo to C16 coming soon....keep you posted

full tune and comparo to C16 coming soon....keep you posted

I used it in my Slot Car at Wakefield yesterday and no problems and car felt strong all day.

I've filled half a tank yesty.... just a question tho... I have a stock ecu.. how do i reset it... and.. do i need to?

Reset does jack....

I had mine on the dyno ~3years ago, did a few little tests - pod vs stock airbox, ecu reset. All showed a zero increase in power anywhere in the rpm.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • Those above shitboxes, mediocre and above usually have a turbo strapped to them, hence the slightly higher octane is required.  
    • Hi all,   long time listener, first time caller   i was wondering if anyone can help me identify a transistor on the climate control unit board that decided to fry itself   I've circled it in the attached photo   any help would be appreciated
    • I mean, I got two VASS engineers to refuse to cert my own coilovers stating those very laws. Appendix B makes it pretty clear what it considers 'Variable Suspension' to be. In my lived experience they can't certify something that isn't actually in the list as something that requires certification. In the VASS engineering checklist they have to complete (LS3/NCOP11) and sign on there is nothing there. All the references inside NCOP11 state that if it's variable by the driver that height needs to maintain 100mm while the car is in motion. It states the car is lowered lowering blocks and other types of things are acceptable. Dialling out a shock is about as 'user adjustable' as changing any other suspension component lol. I wanted to have it signed off to dissuade HWP and RWC testers to state the suspension is legal to avoid having this discussion with them. The real problem is that Police and RWC/Pink/Blue slip people will say it needs engineering, and the engineers will state it doesn't need engineering. It is hugely irritating when aforementioned people get all "i know the rules mate feck off" when they don't, and the actual engineers are pleasant as all hell and do know the rules. Cars failing RWC for things that aren't listed in the RWC requirements is another thing here entirely!
    • I don't. I mean, mine's not a GTR, but it is a 32 with a lot of GTR stuff on it. But regardless, I typically buy from local suppliers. Getting stuff from Japan is seldom worth the pain. Buying from RHDJapan usually ends up in the final total of your basket being about double what you thought it would be, after all the bullshit fees and such are added on.
×
×
  • Create New...