Jump to content
SAU Community

Recommended Posts

What I am saying is that the vortex here is BP ultimate. Its actually 98 ron bp fuel.

The reasoning this guy gave me for caltex not calling it vortex 98 is because the real ron figure can be anywhere between 95-98. BP dont care that its often lower then 98, but caltex promise it to be atleast 95, hence the 95 ron rating.

I still find it all a little wack, were the catlex premium pumps running out at the same time as BPs?

Edited by noise

I used vortex when there was no ultimate and some caltex's were running out. Attendant said that they wouldn't have any until middle of december, thought it was a bit of a coincidence that it was the same time ultimate was meant to be back.

Maybe our vortex is just ultimate that's been cut with lower grade fuel to make it 96 ron.

I've visited Dulux factory and apparently they manufacture competitors paints as well (a specificed ingredients list is provided by the compititor), because it is relatively expensive to buy the machinery, so competitor just 'piggy back' of Dulux...this is why even though more ppl chose to buy rather cheaper generic brands, Dulux never went bankrupt...

imagine that there is only 1 refinery in W.A....so the companies, BP, caltex, other fuels basically come from the same spot, only that different companies have their own "secret ingredient" such that the refinery have to refine these petrol according to the clients specification.

now what if the refinery is owned by BP....BP will process fuel for the competitor..and the competitor sell cheaper fuel ... However, BP needs to keep it's image up..and hence they produce the only 98 Octane Fuel in W.A....BP domination...muahhaha

probably in the case of Eastern State, the amount of population is enough for each individual companies to set up their own refinery and keep it profitable...therefore 4 different 98 octanes to choose from... BP does not dominate the market anymore....

This checks out with the unavailabity of vortex in the same timing as Ultimate...but then again I might be wrong...don't have the fact sheets on me....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have you flushed the initial fluid yet? It should look like a rainbow unicorn shat glitter into it. 2nd or 3rd fluid change is when you party.
    • all brand new unit from Tomei, fluid, bearings, etc. Tomei said they call it a 1.5 lsd because its 100 percent lock up under acceleration and 50 percent under deacceleration.  as I mentioned I used their fluid, install and their break-in procedure, (alot of figure 8's) but even when driving straight, or even slowly backing out of garage for first time, (at 2 mph) then driving to and from figure 8 parking lot, each tire in the rear would sporadically grab, skip, bounce, shutter and skip, shutter back a force I could feel causing clutch to slip then grab, at any speed. shaking entire car. I removed unit, since I put stock back in and all is fine, via process of elimination, its something with the lsd unit itself. I wasn't going to beat up the entire car more or change anything else for no reason as I had a feeling something in the lsd itself was wrong as everything was fine before this alone was installed and I rechecked over everything else after first time backing out I suspected an issue. I'll probably sadly already need new tires now just from trying to drive it 5 miles and performing the figure 8 break in. but if someone has any ideas I'm all ears 
    • Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
×
×
  • Create New...