Jump to content
SAU Community

Recommended Posts

im looking for a big intercooler for my gtr. not sure where to find one. should i be looking for a complete kit? or get the cooler and get piping made up? ive retained the twin turbo setup with larger turbos. i dont want a cheap chinese cooler, rather something good, that flows well and suit a high hp application. what price range am i looking at?

Link to comment
https://www.sau.com.au/forums/topic/95899-aftermarket-gtr-intercooler/
Share on other sites

Next to none of the coolers for the GTR come with piping, you just get the cooler. They range from $1500 - $3000 depending where you get them from, then a complete piping kit is usually around $1000 - $1500 on top from the big manufacturers (HKS, Trust etc).

Just grab a second hand HKS Type R/Trust R-SPL etc from one of the local parts importers, save yourself alot of money and use the stock piping.

Contact Just Jap in Sydney, I was looking at their new intercoolers for GTR which can be had for around $800 and from memory they are a tube and fin core, around 100mm thick.

Cheapest I have seen, and they look to be a pretty decent core as well

Alternatively, im running the Apexi GT spec monster intercooler on my 33 GTR and its one beautifully made intercooler but the cost jumps up to around $1500, mind you the core is 138mm thick - I purchased it from UAS and from what I understand there is limited stock as Apexi no longer manufactures them

Hey Blitz did you have to chop/modify the front bar to fit the cooler, 136mm is quite big!!!

The front bar needed trimming, but I still have the factory mesh in place :)

The core design used on the Apexi GT Spec is by far the best I have seen

sorry, wen i got my car it didnt have the cooler so i didnt kno that it was one in one out. i was looking at an ARC cooler and it had a twin outlet on the right side.. thats y i asked. :P is it worth spending the extra money getting the brand name cooler or are the just jap ones just as good? i dont mind spending the extra cash, if its worth it!

forget that, there are two types of intercoolers one for looks and one for performance.

the diffrence is in the core. the cheapest and best way is to keep everything standard. go to a turbo place i can recommend one in wollongong tel them what dims your intercoller is and just get the core replaced and keep the standard pipeing and everyhting else. also food for thought chrome intercoolers are shit, the best emitter of heat is a black body, so if your serious about your intercooler you need a black one. thats why the standard gtr intercoller is black

i always thought they were black (oem gtr33, gtr32, xr6turbo cores) to hide them as they are not really important to a standard car owner. i think it was abo bob who did some tests with painting them and found that paint altered its properties and made it worse for transferring heat

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...