Jump to content
SAU Community

Recommended Posts

I use 32psi all round, and it feels tight, but not with too much road noise. I guess you should check what is written on your tyre?

I'm not sure about the 40psi mark... sounds like over-inflating when you're talking about stock tyre dimensions?

Link to comment
https://www.sau.com.au/forums/topic/96846-tyre-pressure/#findComment-1758858
Share on other sites

Car manufacturers give recommended tyre pressures that are best for the smoothest ride, not the best handling.

If you like a nice smooth ride, put them to 32psi.

If you want the best handling put it up high like Duncan said around 38-42psi. I always have my tyres at about 38psi.

Link to comment
https://www.sau.com.au/forums/topic/96846-tyre-pressure/#findComment-1760656
Share on other sites

There are 2 main things that happens with higher tyre pressures:

1/ Much firmer tyres, basically the same as fitting firmer shocks.

2/ Less tyre wall flex which is more important on high sidewalls like stock ones. Less difference with big rims/low profile tyres.

I took my old gtst (king springs, 10psi boost, otherwise stock, and with a passenger) around Eastern Creek in 1.57 on road tyres (Falken fk451) at 42psi

Of course it is all totally different with race or r tyres, they have very strong sidewalls and tend to be designed for 30-35 psi hot.

Like shyster said, manufacturers want comfort, not performance :)

Link to comment
https://www.sau.com.au/forums/topic/96846-tyre-pressure/#findComment-1762371
Share on other sites

  • 2 weeks later...

Yeah, I've noticed the same thing. I usually run about 33-34psi in mine (stocko rims/tyres) and I've found that the ride's really good, but the handling sucks; it rolls on the rims. But at higher pressure the corners aren't so hairy, so yeah I'd be going up around 38psi for handling... but for everyday use, the 32psi would do you just fine.

Car manufacturers give recommended tyre pressures that are best for the smoothest ride, not the best handling.

If you like a nice smooth ride, put them to 32psi.

If you want the best handling put it up high like Duncan said around 38-42psi. I always have my tyres at about 38psi.

Link to comment
https://www.sau.com.au/forums/topic/96846-tyre-pressure/#findComment-1816903
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
×
×
  • Create New...