Jump to content
SAU Community

Recommended Posts

  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

jason, just put an aftermarket front bar on it if you want to make it 'angry' so to speak. your car looks very nice as it is mate, love the height and well as how the wheels sets of the entire appearance of the car.

I'd have got a R33 if they weren't $30,000 when I got my R32

The $10,000 dollar differance was they clinching factor for me

I'd swap my 32 for a 33 any day, even with around 200rwkw, I like the feel of a R33, feels more solid and has that big car pressence on the road

R32's interior is dated now while R33 still looks pretty good

either one is going to cost you a shitload if you want to go quicker than stock

Reckon you shouldn't rule out the R33 GTS25T 4dr Sedan, it's a solid option as well. You might find one that comes close to your budget, there aren't as many around, they look great and go as well as anything else around.

Mine came with some wierd ass side skirts and a Nismo style rear spoiler but I'm personally not fussed about the S1 front bar. I actually think that it looks quite alright, even better with the centre section cut out to show off your FMIC (must get around to that one day). And the added bonus, no ground clearance problems like the bigger bars.

Tastefully lowered with a nice set of rims finishes them off nicely.

Plus they don't tend to attract as much of the "wrong" kind of attention!! :(

Good luck with your decision......but I don't reckon you'd be disappointed regardless of which model 'line you end up choosing.

:D

i have a s1, they are gay from the front but for the extra cash is it really woth it?, as it is pretty much the only difference between the two.

you can make it angry! :P

Main diff is the headlights n bonnet between the s1 n 2. but making a S1 look tough can be done by a vented bonnet n 400r front bar :)

Main diff is the headlights n bonnet between the s1 n 2. but making a S1 look tough can be done by a vented bonnet n 400r front bar :D

yer, maybe s2 vented bonnet s2 hedlights and s2 400r front bar!!

altho there is those eyelid things for s1 33... :D

and not to forged the boot lip.. :) i love them, need to get one. :D

Edited by DriftR_33
its an addiction, there are so many differenent things you can do to improve these cars!

I agree.

Drop RB30DETs in them with a nice set of 264cams, gt3540 .82, 3.5" exhaust and have 20-22psi by ~3500rpm, maybe a shade over.. :blink:

or.. If you really want it to rev its nuts off and make 400rwkw...

RB30DET, forged rods/pistons, ati balancer, 272 cams, gt3540 1.06, 4" exhaust and dial in hrmm maybe 26psi, that should be in by a 4000rpm or a shade over and rev nicely to 7.5-8k.

Nice to dream.

Edited by Cubes

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
    • Nah, that is hella wrong. If I do a simple linear between 150°C (0.407v) and 50°C (2.98v) I get the formula Temperature = -38.8651*voltage + 165.8181 It is perfectly correct at 50 and 150, but it is as much as 20° out in the region of 110°C, because the actual data is significantly non-linear there. It is no more than 4° out down at the lowest temperatures, but is is seriously shit almost everywhere. I cannot believe that the instruction is to do a 2 point linear fit. I would say the method I used previously would have to be better.
    • When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
×
×
  • Create New...