Jump to content
SAU Community

Recommended Posts

  • Replies 155
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

  • 4 months later...

no don't use a clear coat.. i found a video on youtube about the paint and the guys says that it has a shine by itself.. i have recently used the red on mine, i'll get a pic soon for you.. i think a couple of other guys on here have used it too..

one guy used red as the base and then used gold over the top and left Nissan writing red, looked really good.

Cheers

Curt

Im a new member and was looking for ways to spruce up the old calipers, thanks for the guide it will go to good use, going with a metallic charcoal and white for the SKYLINE, cheers mate. :D

no don't use a clear coat.. i found a video on youtube about the paint and the guys says that it has a shine by itself.. i have recently used the red on mine, i'll get a pic soon for you.. i think a couple of other guys on here have used it too..

one guy used red as the base and then used gold over the top and left Nissan writing red, looked really good.

Cheers

Curt

Actually, the idea to put a clear coat on it was more to protect the paint and make it easier to wash it. I did the left side of my car and it look pretty good and shinny.

But the problem is that I use foam to apply the paint( because I found, after applying one coat, that the brush didn't work really well) so I can't put grease on my nissan logo. So Is it possible to sand it back to metal ?? I'm asking because I just read on page 5 ( I think or 4) that it take way too much time to sand it back to metal... :P

Edited by cobrAA

i just finished doing mine today. sprayed on the car. did fronts on satday and rears today. duplicolour blue. looks hot!! with the fronts i sanded each coat off after 20 mins or so. stuffed one of my rears cause i put too much blue on :D but not noticable from far away.

so id suggest sanding off in between coats

i just finished doing mine today. sprayed on the car. did fronts on satday and rears today. duplicolour blue. looks hot!! with the fronts i sanded each coat off after 20 mins or so. stuffed one of my rears cause i put too much blue on :D but not noticable from far away.

so id suggest sanding off in between coats

Cheers. I'm going to do mine in the metacast blue, is that what you used...photos?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...