Jump to content
SAU Community

Recommended Posts

I would suggest using electronic cleaning solvent for the afm as it is a fairly sensitive hot wire element in it, spray it leave it for 10 min and do it again just to make sure its cleaned properly wait 10 min before driving . It works a treat as I have used it on both of my cars & my sisters atmo R32

Questions:

How far away do you spray from (don't want to damage the element)

Do you only spray the element or the inside of the AFM casing as well?

How do you know when it's clean? Do you shake it around and watch crap fall out?

Depending on how much oil there is in your intake pipe you may wish to spray with your AFM still attached. Generally I just remove the AFM and clean it separately. You can always remove the intake piping and clean it off the car if you want.

Run your finger around the inside of the AFM. If it's oily, then it could probably do with a clean too.

I use CRC Contact Cleaner. Hold it about 15-20cm from the AFM, and spray in the direction that air passes through. May need to give it a few blasts if you have a lot of oil.

Once it dries (about 30 sec) you should be able to run your finger inside and see that it is clean.

You shouldn't see stuff fall out of it. Generally oil will just stick to the element and the inner plastic.

  • 2 weeks later...

Thanks, I've always wondered :D

but wtf is the AFM

Air flow meter - it basically measures how much air passes into your engine. It's the main input for the computer and a hell of a lot of decisions are made based on that input. Basically if you find the air filter in your car and follow the pipe a little back you should see a piece of "pipe" with some flanges on it and a plug coming out of it. That's your AFM.

Don't use Carby Cleaner on the AFM it leaves a residue afterwards. Use Brake Cleaner or Electrical contact cleaner instead.

Do it on the car if you can get to it, just spray the actual senor wire the rest of the assembley doesnt matter.

Weasel the AFM is after the air filter it is a piece of wire and plastic sitting in the middle of the intake pipe. If it gets dirty it can give incorrect readings to the ECU resulting in missfires

What Duncan Said,,,"Brake Cleaner". It's my mechanic in a Can. Cleans AFM's,,,funny enough brakes (removes spilt brake fluid as well as cleaning brake grunge. This stuff SHOULD be in everybodies toolkit.

I even use it to clean up his oil seepage between races.

If you really want to do a test,,,get a clean piece of glass and spray some carby cleaner,brake cleaner and contact cleaner on it, one at a time and you tell me the results.

Neil.

  • 3 weeks later...

haha. when i cleaned my AFM i used CRC contact cleaner. didnt need much, endded up taking it back. scored $20. booya

i cleanded it too much, long story short. my car was running better when the AFM was dirty (as my car was rooted). so for no reason i decided to try dirty it again... used everything i could find under the sun, as long as it was spray-able. however it wouldnt go dirty again.

anyways got my initial problem fixed and now the car runs fine, with my poor attempts to dirty the AFM.... id clean it again if i didnt have to go back to the shop to get a can of cleaner

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
×
×
  • Create New...