Chris Rogers

there is actually- engine bay relay panel has a few.

org+pur =12v brn+wht = gnd grn+blu= motor clip and tape teh others.

take a photo of the top BEFORE you pull the top off. also fixed your post. I'm not a MSN chat person

start looking at fuses.

nope. that said will it work not screwed/mounted to anything?

ok have you removed the shipping screws? there will be two screws through the top if the unit that will look out of place. remove them and it shoudl work.

where are you and what brand is it?

it was s fuse probelm to my understanding - I gave him a new fuseholder and it seems to be fixed.

look again- you haev a dead fuse. pull each oneout.

short of removeing the rear seat that is the only realy way I can see 2 15" subs in there properly.

stick but dont close (I want to add to it.)

Tacho addition: http://www.apexi-usa.com/pdfWiring/3.pdf (this is the current RSM diagram - gives speed ,tach,ign wiring off ECU) R32 RB20 P23 diagram:N4a R32 GTR RB26 P23 diagram N4B R33: RB25 P23 Diagram N4C R34 - P23 also ------------------------------------- R32 stereo wiring http://www.installdr.com/Harnesses/Nissan-Wiring.pdf when following this diagram the black wire on your radio goes to frame! no where else. --------------------------------------------------------------- R33 stereo wiring - SEE R32 ------------------------------------ R34 Stereo Wiring http://www.installdr.com/Harnesses/Nissan-Wiring.pdf use the 2nd diagram. for R33 S2 - use 2nd diagram. ----------------------------------- V35/M35 base spec: http://www.installdr.com/Harnesses/Nissan-Wiring.pdf 2nd diagram. DO NOT attempt this on a BOSE VERSION! it has an ENTIRELY DIFFERENT SETUP and you WILL kill something. cars later than 05 are CANBUS so be VERY careful here. ------------------------------------ 34 GTR display info inc swapping to non GTR dash. Here's a good guide for transplanting the MFD into an ER34. http://flatout.main.jp/driving/parts/bnr34mfd Here's an excellent guide for transplanting the MFD into an R33 http://www.geocities.jp/yossyi_bcnr33_carbon/inpure/MFD.html An AV cord to output TV onto the MFD (Clarion part #:855-5430-00) http://pub.ne.jp/BNR34/?entry_id=89518 MFD pinouts http://f14.aaa.livedoor.jp/~lindwurm/bnr34/diy/mfd/mfd.htm ---------------------------------------------------- PIVOT START BUTTON http://www.pivotjp.com/download/download-e.html I'll ad to this: if you want something looked up and added PM me dont post it here.

the one I have is VERY close. $15/m and its about 2m wide. I need a R33 to comare with but on a 32 it matches well.

google apexi USA and D/L the current RSM installation manual. then its dead easy. I'll see if I can make it a sticky (vijay help!) since htis is asked at least once a week.

not easily. the whole boot may as well be the box. couldn't you do something a bit mre sensible?

how much do you need I have a 100m roll of the stuff..

unsure - will have to look at it.

yep run it past (ring first.) and I'll have a look.

reggie, pop up a few pics of yours if you have them. pocket is still useable IF you leave the screen down.

it will if you put it on top. put it on the bottom and it JUST clears. need a pocket to fill the void.

Also grab the adpating connectors (assuming the OEM unit is still there.) AP7550 -$15 AP348a -$15 if you need them fire me a PM.

that is the hicas ECU. the one I'm talking about will be off to teh left.

r32 or 33? sounds like it may be bypassed already. look under the back shelf for a round module. if there is a loose plug behind it with a patch plug on it then the job is done for you. its rare that they run without being hooked up in the front (IE powered.)

if you didn't have a air bag it would be a case of unbolt yours and bolt the other in place. since you do - you cannot LEGALLY remove it.

what is on the screen?