The Bogan

And the story line to these pics is ???????

Block it off and do another 2500 then do another test to see if it effects the rseults.

Heres one to show our support to our government sponsers

One for the modifier

Because you are all nerds you have forgotten the ladies, here is my super awesome design for a ladies Tshirt Remember guys, Its all about the ladies

Water % Percentage of water found in sample given as a percentage of total volume. Moisture is common in short trip vehicles that don’t fully get the oil up to operating temperature long enough. It generally takes 10-15 minutes for the oil to get to this temperature, which is enough to start evaporating the moisture in the sample. The same goes for fuel in your sample too. An occasional long highway drive is good for your oil’s health. http://www.bobistheo...e-oil-analysis/ Also, if you run your cars oil at over 70 deg for 30 to 40 min it should burn off any moisture that has accumulated in the oil

Water comes from the atmosphere and the combustion of fuel, one of the byproducts of fuel burning is water, sounds silly but its true, a forged motor will breath heavier until it has come up to temp and allow more contaminants to get past the rings. Same with higher boost, there are some good research papers on this in the interwebs. And E85 will produce even more moisture. Ill look for some linkys on this later IICBA

Oil that just sits in catch can will accumulate all the moisture in the system due to it only staying warm enough the attract moisture and will turn to crud, but if it drains back to the sump from the catch the moisture will be cooked off in the hot oil, my can has been returning to the sump for a couple of years now with no ill effect The vents on top of the catch can allows any moisture in the system to get out. Simples physics like me, simple...

I got it because it was thin, it has better flow than the thicker stuff, and I found how it bends easy was a good thing as you can easily form it and shape it around corners.

REPCO has sheets for $20 ATM

Entry forms will be sent in tomorrow, Hope I make the cut off, I will be sluming it though, Ive got my swag, all I need is a local truck stop. One question from the Gen Supp Regs; 3.5 Fuel is not available at the venue and cars should be sufficiently fuelled prior to arrival at the venue. Due to safety considerations, refueling in the Competitors’ Paddock area is prohibited Can fuel be stored somewhere near by or is no extra fuel allowed on site ? Thanks, Mark

I wanted go go for a month or so (mainly for the fishing) but 17 wanted SME to pay for me, SME said that if 17 wants their assest they would need to pay, 17 had a sook and said they couldnt afford to pay, hence Im still in Sydney, Ha, look at them now, undermanned and no soil or Q & A element with any experience. I hear its arse. Fingers and toes crossed mate.

Hows ACRAP, lOloLoLoLloLllsssss Paul, Eastern Creek on the 22 July, good spot for some "R & D" DO ITTTTTTT

Been talking to my cousin and he picked up a EOI for half the price your asking. Just saying....

Only enough room for a half cage

Red looks good, I want a red one, without a doubt they are the best sporty little thing since the 200. How is the room in the back, OK for kids ?

Please excuse my lame paint skills. Im going to fab up a front splitter out of plywood, the mounting points I want to use are the ones where the reo bolts to the chassis. Im thinking that they would surfice for what I want, from looking around at all sorts of sizes Im thinking about having the splitter sitting about 150mm from the front bar. My only concern is that the front 200mm of the splitter will have no support, BUT, if the brackets are made from say 10 gauge steel ( THICKEST I CAN GET BENT ) and backing plates are used behind the fixtures that join the splitter to the bracket it should be fine. This is a elcheapo style bolt on for track days jobbie. Thoughts, Im thick skinned so cut loose. Thanks, Mark

http://www.sscc.org.au/site/ai1ec_event/supersprint-round-3-interclub/?instance_id=118

$220 early bird or $250 after, ??? 07 July?????. Entry and supp regs are out, I cannot linky yet. They came in a email,but are not on the SSCC site yet, I'll ask if I can post them up later. You may be able to find them on the WRX site though. And its the full GP circuit, YAY.

Same here. Im guessing around $2fity, and if not, a lockness monster

SSCC Inter Club Super Sprint. So, whos keen, I am.

Suspension, brakes, seat/s, harness/s, tyres, oil cooler, a real catch can, ROPS, replace all bushes, 1.5, full service on all the oils and fluids, to start with. Dont overboost it and dont run it on the limiter Is it going on a trailer or stay regoed ? Remove all unneeded fat, carpet, deadener, A/C, trims. Is the car stock or modified ? Money to burn ? carbon everything, full strip rebuild, aero, dash, flashing lights and bells and also whistles, see the superlap site for details ARK DESIGN TIME ATTACK SKYLINE GTR http://www.advanwheels.com.au/racing/car.aspx?id=52 Specifications Engine Nissan VQ35HR by Cosworth Estimated Power 900hp at the wheels Approx. Weight 1200kg Engine Modifications Cosworth built VQ35HR with WPC Treatment on all applicable components, BorgWarner EFR turbocharger, Turbosmart Hypergate 44 wastegates, DC Sports 350z headers modified Suspension & BrakeMods Tubular front double A-arm, Rear revised Nissan multi-link, Stoptech calipers, Project Mu pads, KW Competition 3 way dampers Driveline Modifications OS Giken differentials and triple plate clutch, Holinger Sequential Transmission, Albins crown ring & pinions, Drive Shaft Shop axles and prop shafts Chassis Modifications Design Craft cage and chassis work, Plastics 4 Performance molded acrylic windows Exterior Modifications Veilside widebody with aero modifications by Design Craft and Mike Kojima of MotoIQ, Final Konnexion fiberglass doors and boot lid, Voltex front splitter, front canards, and rear wing Wheels & Tyres Volk Racing RE30 Club Sports and TE37 Super Laps, ARK Design Duraluminum lug nuts, 18 x 11, Hankook Ventus TD 295/30/18 Interior Modifications Sparco steering wheel and 5 point harnesses, ARK Design bucket seat, Cosworth Electronics Pectel SQ6 ECU and Pi Research Sigma Elite datalogger, Pi Omega D3 dash display, Tilton pedal box I need to win LOTTO

Leak down was good, I cannot remember reading but it was apparently OK, head drains were drilled out, has - 12 head drains/vents to sump, has - 12 return from catch can to sump, has 1 x 0.8mm restrictor for the head feed, 1 x 0.6mm for the VCT. The motor was pulled and tolerances double checked. Its fine at the drags, the only time it isnt is when Im getting up it hard and going around corners. I dont know what else to do, my brain hurts bad..

Nothing is ever easy is it, what weight oil you using now ? Thanks, Mark

I may look at getting a lighter synth oil (for drainage), and knocking the oil pressure down to about 80 psi, . I need to do something to slow the volume oil getting into the head. Thanks for the info, Mark