Search the Community

Hi Guys, As topic states, I am searching for a Sparco Group N Quick Release Steering Hub like the one shown below. I am really only after the gold locking mechanism that bolts to the steering wheel, as i already have the spline section that bolts to the boss kit, and want to be able to swap between 2 different steering wheels easily. But if I have to buy the whole thing, then so be it. Let me know what you have, and a price please. Cheers Damo

I am currently rebuilding a R34 GTT gearbox that has a problem getting stuck in 4th gear and unable to down shift from 5th to 3rd even if you rev match (block out condition). Sometimes you have to jerk the shifter to get it to pop out of 4th, but funny enough, all the gears goes in like butter even on full song. All the gears can be selected in/out with the car running, clutch-in whilst on the brakes (i.e. the main shaft not rotating) indicating that it is not clutch drag related. Information on previous rebuild: New bearings and synchros 3rd/4th synchro key popped out, one was found in the drain plug Inspections on tear down during current rebuild: Input shaft end play was checked and within specs Countershaft end play was checked and within specs Synchro gap and grab was checked and within specs (all gears) Synchro teeth condition was good (all gears) 1st/2nd and 3rd/4th synchro keys and spring was in place All bearing condition was good All shift forks had slight wear on where the brass lining were but as expected. No cracks. It was found that 3rd/4th synchro hub and the slider felt loose and was able to rock when assembled compared to the 1st/2nd synchro hub As all the issues are apparent in the 3rd/4th cluster, an educated assumption is that when the 3rd/4th synchro key popped out as per previous rebuild due to play in the hub and slider, more kilometres gave it additional wear that made it so severe that the engaging the slider caused it to be twisted off centre and jam into place, unable to get out of 4th. Is the above a reasonable conclusion to the problem? • TIA •

Fairly simple question, I just cant seem to find an answer to..... Will an R33 GTR front hub fit a C34 stagea? thanks for any help.

Just wondering if anyone has used hub centric spacers for gktech? Curious as to what their quality is like as I'm thinking of purchasing some 15mm ones for my 34 Cheers http://www.gktech.com/index.php/5x114-3-15mm-hub-centric-spacers.html

2006/7 Nissan Skyline PV36 Sedan Hub/Wheel Bearing Needing to replace my hub bearing as the noise is really getting to me... Does anyone have the part number for the front hub bearing? Does anyone have a price or know where to buy it from, other than Nissan?

So after doing the major repairs on my r33 its time to fix the other minor things for quality of life. I need some advice on a few questions 1. Is it better to buy rear hub assemblies(including wheel studs as somehow the previous owner stripped 1 stud both sides) 2nd hand or buy brand new 2. Are rotors being sold on ebay trustworthy as I saw some for $125. 3. What brand rotors are recommended for r33 on the rear (not too expensive for this apprentice mechanic life) 4. If I do get rear aftermarket rotors do I have to make sure they are compatible with my factory calipers (they have Bendix ultimates pads)

HKB boss kit (what is this part?) Hi! I Just recieved my new Personal Neo Grinta steering wheel today and a HKB Hicas sports III non airbag hub (ON-177) to my Skyline r33 gtst series1. I think I have figured out were everything goes except for one thing. Can someone here tell me what this part is and where it goes? im referring to the small silver ring to the right in the picture. The bigger one to the left I believe is a horn adapter? I have googled for hours but didn't find anything about this smaller ring. So If anyone here have a indentical Boss kit or can tell me what it is i'll be happy. Thanks.

Hi everyone, I need your help on getting spacers for my GTR. I thinking of adding 10mm or 15mm but am finding it hard getting the right spacers as the centre bore is the exact size as my current wheels so how do I get spacers that will fit my wheels on top? As you can see from the attached photos, I bought a set of 10mm spacers and the centre bore won't fit through my wheels. I've never looked into spacers before so am needing some help. Specs of 10mm spacers that didn't fit were: PCD: 5/114.3 with 66.1mm center bore and 73.1 OD What specs would I need for them to fit? I only need 10mm or 15mm. Thanks all.