Jump to content
SAU Community

Recommended Posts

that looks like the 18RGU yamaha head engine....i used to have one of those in an RA28,I rebuilt the engine using 18RG non pollution pistons as they has 10.2 comp ratio instead of the "U" engine has 9.2 or there abouts....i stuffed a huge set of cams in it and it was lumpy as all fark....then i done this in the end....i swapped the engine into a ke 30 corolla and then sold the set up to a chap with a ta22 and this is what it looked like

post-2711-1136152748.jpg

lol Ron should stick to his GTR. Didn't he get a celica similar to yours for some guy in Ireland ages ago?

Troy I thought the "U" engines were the non pollution ones?

B Dual standard carbs (only used on non-twin cam engines, obsolete code)

C Californian pollution control (also most of the world)

D Uses leaded fuel (Super) when base engine uses regular

E Electronic Fuel Injection

F Twin Cam (economy)

G Twin Cam (sports) with multiple sidedraft carbs (unless EFI)

H Unknown but never combined with -B or -C

i Single point fuel injection

II Unknown - possibly denotes L.A.S.R.E

J Unknown, possibly autochoke, possibly another anti-pollution control

L Transverse mounted engine (only used around 1985 when transverse was new)

LPG LPG fuel

M Phillipines market (details unknown)

P LPG fuel

R Low compression for regular (not super or premium) fuel.

S Swirl intake ports (only a few made in mid '80s)

S Direct injection & swirl pot pistons (starting from '97/98)

T Turbocharged

U Japanese pollution control (introduction of "U"nleaded?).

Z Supercharged

It has always been my dream to get my hands on a 1GZ and shoe horn it into a tiny car :P

speaking of cramming big things into little bays...

post-256-1136330594.jpgpost-256-1136330620.jpg

also... one of the fellas locally managed to cram a landcruiser V8 under his hood, so its not that far fetched.

that landcruiser V8 looks a hell of a lot like a 1JZGTE

(or is that what they look like without those cover things on em?)

i know theres a couple of spoontas in NZ with 1JZs

that landcruiser V8 looks a hell of a lot like a 1JZGTE

That's coz the one in the pic is a 1JZ ;) AE86 engine bay is about the same size as the celica as well.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • I forgot about my shiny new plates!
    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
×
×
  • Create New...